Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi Nordic Team,
Please suggest logic to scan all peripheral devices by the central device.
In my BLE project when I'm trying to scan all peripheral devices which are advertising...
Hi Nordic Team,
In a BLE project we need to configure same device to conditionally act as central (to scan) device and peripheral(to advertise) device based on the state...
If I write to the MWU REGIONENCLR register and immediately access memory that was previously watch enabled an event is still generated. If I delay a small amount (tested with...
Hello,
we have made our fist device with a custom Service with 5 characteristics. And now we have a strange problem which I was not able to debug to find a solution.
We...
Hello,
if I call this code all works:
if I call following code only ZB_ZCL_ON_OFF_SEND_ON_REQ take effect on target
I'm simply swap the call order, where's the error...
Good morning everyone,
I saw this question asked a few times, but no conversation was actually fixing the issue.
I am developing a product where I want the pairing to...
This seems to have changed in recent SDKs, so that none of the examples or techniques mentioned in previous posts is relevant any more.
I am using the SDK v16.0.0 ble_app_blinky_c_pca10040_s132...
When I carefully follow the instructions at https://infocenter.nordicsemi.com/topic/sdk_tz_v4.0.0/thread_ot_libraries_building.html , I am missing some of the openthread libraries...
Hello.
I just started using nRF52840-DK board with SEGGER Embedded Studio and I'm trying to use it to save data in a micro SD through an adapter. I tested it with the Fatfs...
SDK15, nRF52832, S132
I notice that after about 30-50 bond and delete cycles peripherial to central, central doesn't want to bond. Before it bond and after that delete bond...
Hi there, I am working on controlling the nRF Mesh device (nRF52840-DK) via the bluez version of 5.52 (meshctl). I try to connect to Nordic nRF52840-DK (example <nrf5_SDK_for_Mesh_3...
Good morning,
Is it always required to use Segger J-Link in order to flash Bootloader, Softdevice and Application to a new device?
Could you summarize the different possibilities...
I have an application where I will require an external antenna as our product sits in a metal enclosure.
The example NRF91 DK development board shows a UFL connector (which...
Hi
I want to know the address of the memory used by FDS.
I set the following
I think , this setting uses 3 pages.
However, there are tags at 0x2D000 and 0x2E000...
