Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
'NRFX_SPIM0_INST_IDX' undeclared here (not in a function); did you mean 'NRFX_SPIM_INSTANCE'? error occured .
I am not using SPI , this error is not cured by me .I enable...
Hi
So I'm trying to adapt the ble_lte_gateway example at my nRF9160 DK but because I don't have a Thingy52 I have to use an nRF52840 device, so I wanted to try the sample...
I am working on a wearable design that has standalone modules distributed around the body. Each module will do the same thing, receiving commands to turn LEDs on/off or adjust...
Hi,
I am trying to us one more SWI with nrf_drv_swi_alloc , but returns NO_MEM => means there is not any free.
I looked to source code, and I find SD_SWI_USED is defined...
Hi,
I've added NUS service to my app (nRF52832, peripheral, FreeRTOS based, SDK 15.2, SD132). everything works great with MTU size = 23 bytes.
Now I try to increase...
Hi there,
I found very interesting behavior on casting double variables to integer.
The following code gives me strange result:
double dval = 0.;
int ival = (int...
Hey,
Currently I have been working on a project in which I have to calibrate the range of the bluetooth, basically I need very short range of about a meter.
Could anyone...
Hi,
I have some trouble using TWI : the slave device connected to nrf52 sends an ack signal (seen on scope) but the i2c handler raises an incorrect address error and discards...
Hi,
The device I am using is nRF52840, WLCSP package. Most of the analog IN pins are noted "low frequency I/O only", e.g. pins A5, A6, C7, C8. - I know there are some exceptions...
Hi,
As of now we are using SEGGER Embedded Studio for compilation and Flashing.
Now we would like to copile using Cmake tool, can you please provide template Cmake for...
downloaded thingysdkv210 from thingy website. extracted that file and executed Prerequisites as per the procedure
downloaded Python v3.xx.xx
downloaded Git v2.xx.xx
...
Hi,
I am trying to add CLI Command feature into the example Open_bootloader_usb_mbr, but get error during link stage when compile as below,
Building ‘open_bootloader_usb_mbr_pca10059_debug...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am using multiple interrupts. For example, BLE communication interrupt and SOC interrupt. I set the priority of each interrupt...
Dear Sir,
I have flashed 'ble_app_hrs' code to one of my RIGADO DK.
I have installed nRFConnect App in mobile phone.
When I press the scan button I could see the device...
