I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I have been using the buttonless DFU method for a while on the nrf52832 Chip. Due to performances need we changed the chip for our product from nrf52832 to nrf52840...
So, my understanding of the current support for a PA/LNA is a set of configuration options you can pass into a BLE library and then the soft device will handle the operation...
Hello,
I am interfacing a nRF52 based module with external flash memory.
When I try to program/read a single byte, I get the " NRF_ERROR_INVALID_ADDR" error.
This...
Hi,
I'm trying to develop a custom provisioner for a nRF52840 DK. All I've done at the moment is merely rewriting the Light Switch provisioner example.
The code compiles...
Hi,
I'm writing a central application for the nRF9160 DK. The central connects to an nRF52832 peripheral and subscribes to a characteristic whose CCCD handle and value handle...
Hii,
I am using nRF52840 module in beacon mode which is transmission one value read from sensor. According to code sensor sampling and transmission cycle is controlled by...
Hello,
I have to automatize the programation of a controler nRF52832 with a Segger J-Link EDU programmer in LabVIEW environnement.
Is it possible? Can I find some examples...
Hi,
Bug: The Zephyr LwM2M client does not add resources UTC offset and Timezone to the Device object. Everything is prepared but the actual lines to add them is missing...
Hi,
I have a mesh network with multiple smartphones, which are connected over GATT. If now a light command is triggered on one smartphone, I want to synchronize the other...
Hi Sir,
As we know the SDK has the lowest version of IDE to compile.
========= release note of SDK 16.0 ============
The following toolchains/devices have been used...
Hi,
Every now and then we have to fix bugs in nRF Connect SDK. Some of the bug fixes are of general interest. What is the process for contributing fixes to Github?
BR...
Debugging in Segger serial example from mesh
It runs and responds to commands, but when paused or hits breakpoint - single step or continue gets to address 0xa60, continue...
While setting u p a sample project in SEGGER Embedded Studio, following error is encountered
All the previous installation steps were successful and verified.
Please...
Hi,
I am trying to implement SPI slave on NRF52810. I added nrfx_spis.c and enabled below macros in sdk_config.h
NRFX_SPIS_ENABLED and NRFX_SPIS0_ENABLED to 1
Still...
