Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello,
I just created an application that can count the number of rising edges/events on button presses using the TIMER0 peripheral configured as a COUNTER. So far it is...
I am developing an application for Android and IOS. Faced a problem when try connect nRF Connect as central (on Android) to nRF Connect as peripheral (on IOS)
...
What I need?
I should be able to perform scanning, connecting, disconnecting and accessing service from main() (in a infinite while loop) rather than interrupts. I see that...
Hello,
I'm using SDK16 with the s332-6.1.1 softdevice in ANT mode.
When I request a radio timeslot of 10 ms, that works just fine, but if I do anything longer than approx...
Hello,
we have developed a custom board using the nrf9160 SICA chip and are now modifying the bifravst cat tracker example to suite our needs.
Basicaly, it samples from...
I am trying to get my ublox module to respond to at commands, through the programming of the boron module, which is found in this link, but I don't have much idea of how...
Hi.
I am trying to get mesh DFU working and I keep getting "Failed to upgrade target. Error is: Crashed on start packet" from nrfutil.
When debugging the target I see...
I am using the nrf51822 ble with softdevice and want to know if the broadcast can start at a given time, and if the adv_ interval can change everytime? (such as I want to...
Hi Nordic Community,
I'm trying to run app timer in bootloader_secure. But when I add app_timer.c file to project, it built successfully but breaks when execute. I don't...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board to connect with an iOS(v 13.3) phone.
I am sending data continuously over BLE. However I...
Hi,
I'm trying to find simple ADC code for one shot modus as described in the documentation: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52832...
I will use Nordic nrf52840 dongle for 2FA + security key on Google login and I am following these instructions:
https://github.com/google/OpenSK/blob/master/docs/install...
I use nRF52840 and SDK16 with S140 softdevice. I need 3 ADC ports. The initial code as follows.
static void adc_configure(void) { ret_code_t err_code = nrf_drv_saadc_init...
Hi,
I add a my .ilb file in the ses project .When I c all the function in the .lib file and build, it will have an log "undefined reference to 'xxxx'". But i can success...
I want to upgrade a BLE peripheral firmware (nrf52840) by using another nrf52840 as BLE central.
Do you have any idea how I can do that?
I know how to use android to upgrade...
