Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello.
I just started using nRF52840-DK board with SEGGER Embedded Studio and I'm trying to use it to save data in a micro SD through an adapter. I tested it with the Fatfs...
SDK15, nRF52832, S132
I notice that after about 30-50 bond and delete cycles peripherial to central, central doesn't want to bond. Before it bond and after that delete bond...
Hi there, I am working on controlling the nRF Mesh device (nRF52840-DK) via the bluez version of 5.52 (meshctl). I try to connect to Nordic nRF52840-DK (example <nrf5_SDK_for_Mesh_3...
Good morning,
Is it always required to use Segger J-Link in order to flash Bootloader, Softdevice and Application to a new device?
Could you summarize the different possibilities...
I have an application where I will require an external antenna as our product sits in a metal enclosure.
The example NRF91 DK development board shows a UFL connector (which...
Hi
I want to know the address of the memory used by FDS.
I set the following
I think , this setting uses 3 pages.
However, there are tags at 0x2D000 and 0x2E000...
We have a problem that we are struggling to solve. We have written an application for the Nordic Semiconductor nRF52832 which uses a proprietory radio protocol. This protocol...
Hello,
I have a question about a certain issue that came up during developing a 3 transmitter, 1 receiver setup.
So the basic setup is that the transmitters are sending...
Hi,
I am trying to compile using cmake, all the components[Softdevice, Freertos, Drivers] are built as static libraries.
Using SEGGER Embedded Studio projects compiles...
Hello I am trying to add OTA update functionality to my device which is running the nrf52810 micro with the s113 softdevice. Currently I am trying to convert the PCA10040e...
Hi!
I am working on SES studio and NRF52 DK suit.
I wanted to add ble – service files, other periphral driver and libraries files in one of the example project as per...
Hi I want to change MTU size cuz I want to send more
30bytes.
Now I'd identified only 20 bytes of data being transferred.
I changed the MTU SIZE, but it does not become...
Hi,
I set TX power for ble_app_uart application like this;
advertising
sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_advertising.adv_handle , 4);
peripheral...
Dear Nordic,
just got my Thingy:91 out of the box and followed the instruction.
Very surprised that the device could not connect (blue led flashing slowly every 5sec...
Hello
I am a beginner for NRF52832 FW desgin.
Now there are some issue stuck me
The scenario could me show as below: IDE platfrom: Embedded Studio Release 4.12 SDK...
