Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi all,
We want to create some smart home networks based on BLE Mesh.
1. Is it possible to buy Nordic Thingy, load our software (temperature sensor based on BLE Mesh)...
Hi sir We have requirement Blutooth 5.0 for iot Appication. please can you share the schematic file
their is orcad capture design file or available or PDF file
Currently evaluating Bluetooth mesh and trying to use the Zephyr mesh_demo.
I added so that the instead of buttons triggering the bt_mesh_model_send from the main loop periodically...
now I'm on NRF24Le1 project, and I have a problem with wakeup TICK from timer or voltage level on pin (analog comparator wakeup). could you help me ? or have you an example...
Hi,
Is assisted GPS(AGPS) supported in nRF9160?
Our nrf9160 custom board takes 2 to 5 minutes for the first fix with active antenna. Does nrf9160 support AGPS data to...
Hi,
We recently purchased a thingy 52 for evaluation H/W 1.1.0 F/W 2.0.1
We are using an iPhone 8 with the latest Nordic apps.
When we connect using the the Thingy app...
I am new in nordic and just getting started with the nRF52832-DK. . Can someone please help me ? How to read 4 Digital Input and store it into SD card.and then pass that stored...
Hi,
I was using SDK 1.0.0 earlier.
I ported my code to new SDK v1.0.0.
But i am getting undeclared macro error as shown in below image
In prj.conf i have initialized...
Hi All,
I have arduino ble 33 ble device and able to connect with it using my android application using BLE library. I am trying to write 9000 or 18000 of UINT16 by converting...
hi ,,, i am getting the four data from various sensors, then i want to combine all the four data and send in ble_app in variable , example x=10;y=30;z=34 using sprintf i am...
Hi,
I want to use the nRF Mesh SDK on nRF52840 chip with proxy client role that can send messages over GATT connection to proxy server role device. Is that possible?
Currently...
Hi Nordic,
Chip set: nRF52840
SDK: 15.3.0
Softdevice: S140 (06.01.01)
Button interface with MCU: Total=13 (All with GPIOTE)
We have face one blocking issue at...
Hi, Greetings !
I have totally 3 services and 8 characteristics added in my project. In first service there are 2 characteristics, 2 nd service there are 5 characteristics...
Hello Support Team,
I am using an nrf52832 module in our project. During testing, we have observed that the BLE firmware gets stuck and it stops advertising further when...
