Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have been programming nRF9160 using v0.4.0 SDK and it has worked fine. However moving the same program to Nordic Thingy 91 has been giving me problems. The board nrf9160_pca20035ns...
Hi,
Creating an new app will only call the main() in the form of task, i have requirement to create couple of task in my main() so is it possible to create user defined...
Hello,
I'm trying to run Simple_mqtt code on developement board with nRF9160. Connection to LTE takes in my opinion very long time. On basic AT sample code it's connecting...
I am able to build my project, but when I try to flash it to the board via ninja flash_<target> I can select the device in nrfjprog.py, I know, that I have to use "'0'" as...
I am attempting to add a UART to interface to an external MCU. I have the uart example running (without any RTT info) yet when I port the uart code to the ble-thread example...
Is it possible or there is support in nrf52840 such that I can enable readback protection from the firmware itself?
I found an APPROTECT register in bitfields. But how to...
Hello,
I have one custom board which have Nordic's nrf52840 chip. I'm using this chip to scan the surrounding beacons.
For beacon scanning i have integrated Bluez stack...
Dear All,
I tried to take the Capp sense example and implement it in my beacon app which was based on the beacon app example. I am using nrf52382 and sdk16 , segger version...
Hello,
I'm working on nrf52832 dfu secure bootloader example.I implemented button less example to update my firmware and it works fine.
Now i switch off the power supply...
HI , I used NRF52832 SDK15.3,examples:ble_app_ancs_c.When i testing ANCS,I deleted the pm_handler_secure_on_connection(p_ble_evt) in the ble_evt_handler function, The BLE...
Hi All,
I have one custom board based on IMX6UL on which i'm using Nordic's nrf52840 chip.
I'm using zephyr's hci_uart sample application on nrf52840 for beacon scanning...
Hi all,
Greetings of the day.
Here I am not able to flash the code which is built with IAR platform. We tried loading the IAR based blinky example project from the SDK...
Hi all,
Greetings of the day.
Here I am not able to flash the code which is built with IAR platform. We tried loading the IAR based blinky example project from the SDK...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
How do i use a single serial port to communicate with the server...
