Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
After reviewing this thread https://devzone.nordicsemi.com/f/nordic-q-a/53743/zigbee-sdk-on-top-of-freertos I managed to get FreeRTOS working with ZigBee and BLE using the...
On the development boards, the JLink OB stops working after 24 days and needs to be disconnected to work again.
This affects at least the USB UART endpoint, but possible...
I have seen some situations where putting the modem into offline mode (CFUN=4) will cause my application to lock up because the at_cmd never returns. It looks like this is...
Hi, I am using Mesh SDK 4.0.0 and have couple of nRF52840 dev kits.
1) In light switch server example of Mesh SDK, is it possible to add more on_off data types to the server...
Hello I am trying to develop an application for advertising in SLOW mode.
Here is my Advertising Init function.
/**@brief Function for initializing the Advertising...
Can somebody help me out the reason behind below failure on thingy 91. I am building asset tracker example using west on command line. Following is the logs that i got after...
Hi,
I am working on the Thingy91 and trying to set up an event when the USB power state changes (USB cable w/power is plugged or unplugged). For now I will just blink...
Hi,
I changed the softdevice on the nRF52833 light client example from the S113 to the S140, but the program
hangs at startup before even enter the main loop (catched...
Hi ,
During the review, I came across the certification question. After some reading, I found some details.
This got me worried because it looks like it is a difficult...
I have found the example using nRF52833 in the latest SDK (ble_app_att_mtu_through....)
I am using Keil uVision 5.29.0 and I have downloaded the software packs 8.27.1, 8...
Hii,
Our input voltage to nrf52840 is 2 volt, we want to know whether 2 volt will be detected has low(0) or high(1) or undetermined state.we are using gpio pins (1,10) and...
Hello,
I'm considering writing BLE relay application, where central side should bond and encrypt connections (cause sensor device requires it and will not function without...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
I want to add a global variable that would increase every time the timer handler is called. I can't get it to work with static, volatile, or even pass on as variable. the...
Dear all,
I am very new to BLE developments and Nordic product, I have purchased the nRF52840 dongle to have a feeling on the product ( I understand I should get the nRF52840...
