hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I have test setup consisting of 2 boards, one that sends a packet every 2 seconds with CTE, and another with a 2-antenna array that generates MagPhase samples and sends...
Hi,
I am using "http_upgrade_ota" project.
I have added UARTE2 , SPIM3 and WDT peripherals in the application.
To use this peripherals i had to make change in "spm...
Hello, I have developed an application that advertises, connects, pairs/bonds using SEC_JUST_WORKS configuration, and then transmits data at ~2 second intervals to a smartphone...
I would like to use NRF Desktop Connect to connect to, and potentially firmware update an nrf52832 via the onboard bluetooth, but the NRF Desktop connect is only available...
Goodmorning,
I developing an application on nrf52840 board with SDK15.2.0 that communicates via BLE with from the APP nordic. I am started from the example project ble_app_cscs...
So I'm trying to implement Mesh OnOff server with BLE DFU supports. My implementation is as follows:
These are my app_config.h and nrf_mesh_config_app.h
I face...
Hello,
I am trying to use several Thingy 52 as peripheral devices, (sensors) connected to a central (Gateway) particle Argon running ( nRF52840). The idea is to connect...
Hi, I have 2 questions regarding multiple controllers using nRF Mesh.
1. I used the import/export option to transfer the network details from Phone 1 to Phone 2. After import...
now I'm on going NRF24LE1 project to low power mode. I try to find several reference as link below, but both of them can't open, someone can help me ?
https://www.nordicsemi...
I have just purchased a nRF52840-DK
I am following the getting started tutorial and when I scan for devices the Nordic_prox device is not appearing in the device list but...
Is it possible to use the NRF cloud outside the dev kits? Working on a custom pcb with custom software and would like to use NRF cloud for it.
---- Christopher
Hi ,
I am working on NRF DFU firmware update. for that i am using secure bootloader code .
I tried with the of way of flasing bootloader code on my custom board and sent...
Hello Nordic community,
I updated latest modem firmware v1.1.0 in nRF9160 custom board. After flashing application code into custom hardware I power off and power on board...
Hello,
I have a question about hardware for Bluetooth LE Audio.
I see Nordic is working on a dev kit:
https://blog.nordicsemi.com/getconnected/le-audio-unveiled-as-the...
HI
I am programming NRF52840 dongle using nrf52840 dk
i have flashed blinky code to my nrf52840 dongle it programmed sucessfully after that i have erased the dongle by...
