Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi,
I have a mesh network with multiple smartphones, which are connected over GATT. If now a light command is triggered on one smartphone, I want to synchronize the other...
Hi Sir,
As we know the SDK has the lowest version of IDE to compile.
========= release note of SDK 16.0 ============
The following toolchains/devices have been used...
Hi,
Every now and then we have to fix bugs in nRF Connect SDK. Some of the bug fixes are of general interest. What is the process for contributing fixes to Github?
BR...
Debugging in Segger serial example from mesh
It runs and responds to commands, but when paused or hits breakpoint - single step or continue gets to address 0xa60, continue...
While setting u p a sample project in SEGGER Embedded Studio, following error is encountered
All the previous installation steps were successful and verified.
Please...
Hi,
I am trying to implement SPI slave on NRF52810. I added nrfx_spis.c and enabled below macros in sdk_config.h
NRFX_SPIS_ENABLED and NRFX_SPIS0_ENABLED to 1
Still...
Hi all,
I am using SDK 15.3 with NRF52811 chip.
My application include app + bootloader.
In my application, I use flash area from 2E000 to 2F000 for save my user data...
hello
i want to create for the need of my project a thread border router as simple and compact as possible.
i have seen the implementation using a raspberry pi 3B as the...
Hi,
I followed this guide to send data to the GCP using the Thingy:91 : https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-connect-nrf91-to-google-cloud...
Hello,
i'm trying to set the automated test script as described here:
https://github.com/NordicSemiconductor/Android-nRF-Connect/blob/master/documentation/Automated%20tests...
Hi all,
I am a newbie in ble and also nordic. I have an application need that would do some lowfi sound data transfer which 16 bits at 14k sample rate from central device...
Hi,
Good Day!
Statement of problem: Currently we are using app_timer in our application for conducting the user behavior. For example, for user input off of capacitive...
Hello, everyone. I am newbie in use the Power Profiler Kit I followed all the steps as described in PPK User Guide v2.2:
1 - cut traces on the DK (SB40) 2 - installed the...
Hi,
I am porting a BLE program in nRF52832 EVB, and it can work correct.
The system will not work when I want to remove 32KHz crystal from my own real board.
Would you...
Hi,
So we are currently debugging our custom nrf52832 board. It is equipped with both a 32.768khz and 32Mhz Oscillator, which both SEEM to work.
I tested both using the...
