Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
I am porting a software to the nRF52 SDK16.0 . This software uses Floating Point numbers with Exponent-Byte=0x7F to signal Error conditions (then treated as unsigned...
Hi. I want to evaluate the current consumption of the nrf9160 module (I have a Thingy91) and I want to disable all logging functions. I started with the mqtt_simple example...
I have a characteristic with variable length and max length of
NRF_SDH_BLE_GATT_MAX_MTU_SIZE - 3
i.e. the max possible data length based on the max MTU.
During connection...
My Thingy:91 was added to nRF Cloud using "+" > "LTE Device" and then "Already have an active SIM? Skip this step" (iBASIS roaming doesn't work properly in Switzerland so...
I've been trying to get the MQTT simple sample started however after changing the hostname to "mqtt.eclipse.org" and running the sample, it stops with this error. Please how...
Hello, I am using NRF51822. I want to run UART communication on two different baud rates for 2 different hardware on pin number P09(TX) and P11(RX) respectively. I have to...
The queued writes library provides AUTH and EXECUTE events, but I think it also needs a CANCEL event.
In my code, when I receive an AUTH event I obtain the data buffer using...
Hi,
I got a brand new nRF916 DK. I updated the modem firmware to mfw_nrf9160_1.1.0 and updated the application firmware Asset tracker with nrf9160dk_asset_tracker_nbiot_legacy_pco_2019...
I have set up a PA / LNA and watched the radio details.
When the connection interval was 50ms, it was confirmed that the device was communicating every 50ms.
Look at...
Hello
I want to program and debug NRF52840 dongle using jlink But the jlink is not able to find the target . i am using SEGGER J-Link Commander V6.60d application for flashing...
Hi, Sir:
I am using nrf9160 to develop a project of mqtt and GPS, using mqtt to upload GPS data to the cloud server; I use the software and hardware information as follows...
Hi! We were wondering if the Nordic Thingy 91 has an IP-rating? How resistant is it to humidity and could it be deployed in remote locations such as a forest for a prolonged...
Hello,
I have made my custom application and added that in the SDK example folder and I am able to run the project. But after that when I was cleaning my project I got...
Hello everyone,
I trying to firmware update my nrf52832 via Tx and Rx pin uart. I create my own application using keil compiled get .hex file i upload this hex file into...
