Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Dear all,
I'm trying to go to SYSTEMOFF mode and then wake up from activity on UART rx pin (nrf51822).
If I do this:
nrf_uart_txrx_pins_set(NRF_UART0,NRF_UART_PSEL_DISCONNECTED...
Hello, I have a BLE peripheral, that should receive larger amounts of data using a l2cap channel. The central (a MacBook) creates the L2CAP channel, the channel is purely...
Hello,
we develop an open source framework that we are currently extending to also support the BLE Mesh Access Layer Models. We are currently implementing the foundation...
I am using nrf52810, using sdk15.2, softdevice6.1.0, my application flash takes up 56KB (I used fds), softdevice: 100KB and bootloader: 24KB, resulting in insufficient flash...
Hi,
I'm try to test my nRF52833DK using the nRF connect Direst Test Mode. Even if I flash the DTM binaries in nRF5 SDK 16, the Direct Test Mode app says something like ...
Dear Sir.
I am using SPI as follows.
gpio_pin_write(dev_io, LIS2DH12_CS_PIN, false); err = spi_transceive(spi_dev1, &spi_cfg1, &tx, &rx); gpio_pin_write(dev_io, LIS2DH12_CS_PIN...
The firmware is based on the BLE UART example running on an nRF52832 with the S132 softdevice. The first batch of boards were build with the QFABB0 chip revision of the nRF52832...
I have set up APP_BLE_CONN_CFG_TAG with
#define APP_BLE_CONN_CFG_TAG 1
Setting things up in ble_stack_init exacly the way it is done in the example, but when I run sd_ble_gap_connect...
Hi,
I am using nRF52840 S140 V7.0.1. I have few queries on GPIO configurations.
Below are my PULLUP/PULLDOWN macros.
As per my understanding
1) In below settings...
/**@brief 128-bit service UUID for the Apple Notification Center Service. */ ble_uuid128_t const ble_hrs_base_uuid128 = { { // 7905F431-B5CE-4E99-A40F-4B1E122D00D0 0xd0, 0x00...
Hi,
I am using nRF52840, S140 7.0.1. I am using ble_app_blinky application.
Till now I was configuring one board as Connectable Advertiser and other device as Central...
Hello Nordic support,
I am using the usb_msc example with an SD card. When I check this example on a Windows 10 machine, I observe data transfer rate of 355 Kbps. Is it...
