Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
NRF52840
S140
App based on ble_app_multilink_central.
I have tried to build a bridge between BLE peripheral and PC.
I have spend so many time on PC side app.
The...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Dear Forum,
I have an nrf54l15 device and I would like to send a pure sinusoidal tone and measure the phase difference, retrieve I/Q values at the other device. This is...
Hi! I am designing a nRF54 based motion tracker that has an IMU onboard which can take an external clock signal for improved timing accuracy. Initially I had thought of just...
Hello,
I am having an issue using GPIO P0.03 as a button input in my design. Unfortunately, I did not notice that this pin is marked as a dedicated pin for the GRTC peripheral...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
Hi! It seems that I may have uploaded a non-working application to the Thingy91x. Therefore Device is not conectable via USB. The device is responding only in "MCUBOOT" mode...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
Hello all, I am writing this as I am very new to Studio visual code, nrf connect, and many various things used in this project. Currently I am using the two samples given...
dear all,
We are fighting with a problem that defied every effort to solve it so far, so we are asking for help. Our custom board is based on the nrf5340 SoC connected via...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi, I have created my own hardware with nRF54L15 – 2xLED, 2xPWM, and Radio (BLE). I am trying to create a custom board using the graphical wizard. LED and PWM seems to work...
