I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
I was using SDK 1.0.0 earlier.
I ported my code to new SDK v1.0.0.
But i am getting undeclared macro error as shown in below image
In prj.conf i have initialized...
Hi All,
I have arduino ble 33 ble device and able to connect with it using my android application using BLE library. I am trying to write 9000 or 18000 of UINT16 by converting...
hi ,,, i am getting the four data from various sensors, then i want to combine all the four data and send in ble_app in variable , example x=10;y=30;z=34 using sprintf i am...
Hi,
I want to use the nRF Mesh SDK on nRF52840 chip with proxy client role that can send messages over GATT connection to proxy server role device. Is that possible?
Currently...
Hi Nordic,
Chip set: nRF52840
SDK: 15.3.0
Softdevice: S140 (06.01.01)
Button interface with MCU: Total=13 (All with GPIOTE)
We have face one blocking issue at...
Hi, Greetings !
I have totally 3 services and 8 characteristics added in my project. In first service there are 2 characteristics, 2 nd service there are 5 characteristics...
Hello Support Team,
I am using an nrf52832 module in our project. During testing, we have observed that the BLE firmware gets stuck and it stops advertising further when...
HEllo; I'm working with nrf52832 and sdk15 , and for interrupt button i chose to work with the example "/nRF5_SDK_15.0.0_a53641a/examples/peripheral/pin_change_int/" , so...
I am interested in having nRF Connect Desktop Bluetooth low energy app work with my PCA10056. From:
https://devzone.nordicsemi.com/f/nordic-q-a/40155/custom-board-support...
I am trying to connect two peripherals to one central. I do not understand the settings for connection interval and gap event length.
For example, this would result in...
In order to interact with the UART, you need to first declare a device struct and then get a binding to the device:
Then in order to switch the UART on and off you...
I use two nRF52840 to send notifications every second. Analysis using a logic analyzer revealed that the reception interval had strange variations. What is causing this? Why...
I am have a curious issue with thingy52-mesh-provisioning-demo repo at Nordic Semi github.
Prebuild hex behavior does not match with hex compiled by source.
In short,...
hie,
i trying to storage the data in flash and read it. i am unable to read the flash .i have attached my code.please correct me if there is any mistake.
Regards,...
