Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
I have an external flash ( via QSPI ) working on NRF52840 Based product.
I'd like to redirect all NRF_LOG message to a file , is there a similar log backend available...
Dear developers,
My device uses the NRF52840 SoC and is equipped with a modem for internet access.
To perform firmware upgrade, I imagine I would have to download a DFU...
Hello, I tried to work with nRF52832 to read adxl362 registers, Here is my function to read all 3 received bytes from adxl362 (according to datasheets, the last byte must...
Hi,
I tried to install the latest sniffer v3.0.0 and Wireshark v3.2.0 on my computer. I could not see PCA10056 listed. If I start my wireshark from command line, with "open...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send data from sensor over bluetooth...
When i used Port 0 assigned on Uarte rx tx pin , everything was ok.
But when i changed the rx tx pin to port 1 , for example p1.00,p1.08.p1.09, it doznt work...
i am sure...
I use nrf5_SDK_for_Mesh_v3.2.0_src , nRF5_SDK_15.3.0_59ac345 and board pca10040.
Copy the ble_app_uart_coexist folder into the examples/ble_peripheral folder at your nRF5...
Hello.
I'm doing a DFU customization now.
However, because of the problem of data transmission of the last packet of the first page when advertising,
connection and...
I am setting up a relatively complex project that runs on top of FreeRTOS and it is based on the HRS freertos sample app from SDK 16.0.0. The device will need to run in several...
Hello,
I am trying to setup a PAN coordinator by following these steps:
1. mlme_reset_req() -> successfully responds with a mlme_reset_conf_t by calling the callback...
Hi,
I am using 52840 (WLCSP package) in a design. I am a hardware guy and no SW guy has been assigned to this yet. Can you please check my SPI pin assignment below and let...
Hi, I want to know if it is possible to use IOT sim card in India. Is there in any network provide such sim-card? Other than that, which example in SDK I should refer for...
