Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi.
I am trying to start development using Thingy:52. To start, I tried the firmware from the download page ( https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms...
The Limitations subsection of the Zigbee Section here contains the following paragraph:
- OTA DFU: Migration from the nRF5 SDK for Thread and Zigbee version earlier than...
After installing nRFgo Studio v1.17.1 on Windows 7 64 Bit (using the administrator account), I get an error message in the Log section just when I start the program:
"JLinkARM...
I'm using SDK 14 and trying to build the ble_app_buttonless_dfu example. I'm using Linux environment, so gcc for building. When I try to build the example I'm getting an error...
Hi, I was just wondering why there is a "nrf_delay_ms(200);" in the SPI Master example in SDK 16.0.
Here is the code in the main function where it is located :
while ...
Hi Support,
Now I am developing over Nordic 52840 DK (PCA10056). My environment as below,
(1) upon SDK (nRF5_SDK_15.3.0_59ac345)
(2) softdevice s140_nrf52_6.1.1_softdevice...
Hello,
I am using the nRF SDK for Mesh v.3.1.0. To achieve periodic publishing, I set p_pubstate -> publish_period . step_num = 1 instead of zero in the configure step in...
Hi,
I plan to design my own hardware based around nRF9160. Prior to this, I want to verify that I can use the nRF9160DK as a debugger for my own board. As an initial test...
Hello,
We would like to develop a wireless sensor network using the 802.15.4 stack in nRF SDK.
I wanted to know if it is possible to port the existing 802.15.4 example...
Hi,
I'm evaluating the Raytac MDBT50Q devkit, using nRF52840-DK to program it. I'm testing the system with SDK project nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c...
Hi. I am currently evaluating nrf9160 on a Thingy 91 board and have the environment for the asset_tracker application up and running.
I want to be able to handle JSON messages...
Hi,
I would like to have a system such as follows:
Taking sensor data storing it locally till around 100 samples (Once per second)
Log this data to the SD with a time...
Hello,
I was wondering if there are production ready fully pre-certified modules for the nRF91 Cellular chips? Like what Rigado (u-blox has it now) made with the BMD series...
Hi,
I would like to use the nRF52840 dongle to connect to 8 devices using Ant+ and to around 8-24 devices using Bluetooth.
Is there a maximum number of devices of Ant...
Hello to everyone,
I've just started playing with NRF52 DK (NRF52832 SoC). It is my first time with ARM MCU. I've had prior experience with atmega328p and MSP430. Although...
