Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) Previously we had a custom board...
Hi,
I was testing the various cases for DFU & I was looking for any possible solutions to fix the issue.
I flashed SD + bootloader (secure) + app from SDK 15.2 on the...
Hello,
I´m trying to update the certificate of my nRF9160-DK. To do this the modem has to be in offline state. I´m running the AT Client sample like it is shown in the chapter...
I am curious if there is an inherit maximum transmit duty cycle of either M1 or the nRF9160. I am asking for this because we need these numbers for SAR test. Our product will...
Hi All,
I am working on a project with NRF52840 , we are looking for a solution to do the OTA to device by the central device , both of them are using NRF52840 as BLE module...
Hi, I need to be able to count the number of packet Tx and Rx from one board to another in order to compute a packet loss ratio for certification purpose. To achieve this...
hi all:
Use PPI+timer+adc, in the following ways:
called stop, then unable to start adc, Couldn't get into the NRF_DRV_SAADC_EVT_DONE.
Could you tell me how?
Hi,
My product is undergoing susceptibility test and strange issue is happening after the test for 1-2 hours, ie while trying to send data with higher MTU size notification...
Hi!
I have an issue with log-entrys disappearing seemingly at random. Not super frequent and possibly (but not confirmed) more often towards the beginning of a freshly started...
Has anyone been able to successfully setup a Segger Embedded Studio project to step through the Bootloader included in the nRF5 SDK for Mesh ( https://infocenter.nordicsemi...
Hello to everyone and thanks in advance.
First of all, im new at this and would i might be asking something stupid.
I have a development, that one of the features would...
I see in NRF5 SDK ShockBurst compatible mode and relevant support.
I dont see such thing in Bluetooth core5 specification. So - ShockBurst is you proprietary creature ?...
I see the messy information elsewhere especially in selling infos about antennas for BLE5. OK optimal antenna is a quarter length of average wavelength -( 299 792 458 ) /...
I ordered nrf52-dk.
I am trying to install the SDK using nrf Connect Desktop using the option below:
Getting Started Assistant Guide to set up the nRF Connect SDK
I...
