When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I can control GPIO P0,but can't control P1, when I load project with nrf5340_dk_nrf5340_cpuapp ns configuration.
If I load project with nrf5340_dk_nrf5340_cpuapp configuration...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board to connect with an iOS(v 13.3) phone.
I am running a custom application which uses the...
At this time my project is at very beginning state, I am picking up right tools to start my project development. I have spent good amount of time to research about my issue...
Hi,
So simple question about adapting dev kit examples for the dongle. I'm trying to adapt this USB/BLE example and I've made all the changes that I figured I'd need to...
Hello,
I'm currently levelling up a project based on an older SDK which involved SoftDevice v5 (S132) to SoftDevice v7 (S140).
As far as I understand S132 and S140 are...
Hello,
following the peripheral/saadc sample, which shows the periodic reading... could you please share the essential and minimal config for the One-Shot measurement? ...
I want to integrate the XMOS (XUF216-512-tq128) with nRF52840 where the nRF can be used to perform the field updates for the XMOS. Is there an application note or an example...
hello,
i am using nrf52832 device with soft device of S132.
i am trying to connect 2 different applications on the same smartphone to the peripheral device. currently...
I have two NRF52840 dev kits that are running what are essentially the spi master and spi slave examples. They both work and I've altered them slightly. I'm just kind of confused...
Hi,
I've been trying to combine the spi_slave and USB_CDC_ADM examples so that I can pipe data from a spi_master all the way to my host machine. In my cobbled together...
Hello ,
Is there any development KIT available for the Evaluation of Direction FInding - AoA and AoD ? Any code examples for the same?
If not what is the time line?
...
Good day,
I would like to switch between two states once I receive a trigger. state1 <---trigger--->state2.
State1 = Beacon/custom manufacturing data - Beacon Example...
Hi,
In my application after some timeout i am trying to stop BLE advertisement.
for this i am checking current connection state,If it is connected or disconnected.
if...
I'm using the TWI_MNGR to schedule a transfer. I have copied the nrf_twi_mngr_perform() function to a function called nrf_twi_mngr_schedule() which does everything except...
Hi team,
I am working with the nRF5340 PDK v0.8.0 and I am trying to request the additional voltage for the VREGRADIO to support the additional 3 dB TX power on the RADIO...