Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
im looking for a developer that can help me work with the NTN functionality of the 3GPP release 17 of the NRF9151-DK so if you are interested please write to me at eric@zerocool...
Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Yeah. It's that topic again.
I tried to measure the current with an oscilloscope (Agilent 100Mhz; 2GSa/s).. but that didn't quite work.
Can you maybe share how you guys...
Hi
I have tried to convert ble_app_uart to use spi slave rather than the uart with no success.
Please can I have some pointers as how to go about it.
Thank you
Hi,
system info:
SDK: v6.0.0.43681
S110 V7.0.0
nRF51822 Rev.2
I’m using a ~4ms one shot timer (using the timer library) which is being started in the...
How can I dynamically assign the MQTT broker address
Hi all,
I have a general question how to assign the MQTT broker address dynamically.
Current Nordic IoT-SDK mqtt...
Hi,
my question is related to this question:
devzone.nordicsemi.com/.../
Erasing Flash pages takes a pretty long time (and the CPU is blocked during this time). For...
Hi,
I use NRF51822 QFAC chip, SDK is 8.1.1, soft device is S110. The base project is ble_app_uart. Now I want to add OTA DFU into my project. But I don't know how to start...
Hey together,
I'm using the GPREGRET register at the nrf52832 to determine how the module should start up after an off mode reset. Thus I set a predefined bit in the GPREGRET...
I have been working on the multilink example lately (version: 8.0), I have identified the function to send data on the peripheral part, it is sd_ble_gatts_hvx(), but I'm having...
hello ,
my IDE is keil and the sdk is nRF51_SDK_10. i know the system is 16M frequency,but now i only have 32M crystal.How can i change the sdk if i wang to run the system...
hello , Nordic Engineers. my IDE is keil and the sdk is nRF51_SDK_10 and s110_nrf51_8.0.0_softdevice.hex. The project is "C:\Users\robben\Desktop\nRF51_SDK_10\nRF51_SDK_10...
Hi,
I am trying to load hex file over the air for nordic but I am getting error as master emulator installation not found. Please suggest. I am using MCP of version 3.10...
hello i want To use mbed for nrf51 dk. i used this link developer.mbed.org/.../ . i am following steps but i can't copy hex file into bootloader. i got error message "There...
Hi,all
my question is in the title.
i am making a project like NUS (sample in SDK).
i found that during the data transmission Situation，the write without response...
