Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi, all. I use nrf52 and softdevice(S132).
I'd like to know SoftDevice process timing to hardware.
Can it be ?
I know, SoftDevice Specification in "Processor availability...
Hello,
I have an development kit NRF51 and wrote a code for it which uses uart, ble advertising and ble scan. It works pretty well on the kit.
The problem is when I...
Hi,
I use a personnal GAP Address, but it must be the type used:
-Public address.
-Random Static address.
-Private Resolvable address.
-Private Non-Resolvable address...
Hi,
I am trying to get the dfu single bank bootloader ( github.com/.../nrf51-dfu-single-bank-ble) supplied by Nordic to work. I can successfully push firmware to my device...
Hi, I am just trying to understand the examples properly. This value is mostly set to 0, sometimes set to 1, and used at the call to the soft device initialization.
ble_enable_params...
I'm trying to send some data to a custom event handler function using app_scheduler. The problem I am having is the data I am sending is not being received.
I expect this...
Dir sir,
I noticed that you are using the internal LDO regulator in nRF51822 beacon kit.
Why do you recommend to use LDO regulator for Coin Cell battery?
In addition...
Hello,
in my Scatternet, I often receive HCI Connection Timeouts. Depending on the settings this happens once or twice over half a day between 10 Nodes or it could happen...
When I email myself a .zip containing the SDK8-type DFU payload, I can no longer "long press" on the email attachment and have it opened in nRF Toolbox. Either the jackballs...
I'm working on an health thermometer.
I have used the HTS service to send temperature measures from the device to the phone.
Now, the device has to send an alert to the...
Hi,
I have two nrf51 devices one is the master and other a slave device. I need to lock these two devices permanently. What I mean is that these two devices can only connect...
Hi All,
I would like to setup my Eclipse and GCC for compiling and debugging C++ & mbed projects on nRF51 DK. The setup procedure explained in tutorial Development with...
Hi, I use SDK 10.0,
SoftDevice S110 8.0, S120 2.1, or S130 1.0, (I test various examples so I change SoftDevices)
iPhone 6 Plus (iOS 9.2.1), and Nexus 5 (Android 6.0...
Hello, i have a Nordic Nrf51822 ,PCA10001 V2.0.0 EVkit. I am desperately trying to run a beacon code in my EvKit. Since the PCA10001 V2.2.0 is old version ,it only supports...
Hi, i try to understand how to use power down modes. But i have a problem in the example ( nRF24LE1 REGISTER RETENTION TIMER ON ).
while(1)
{
// Register retention mode...
