Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
We use the Nordic UART Service in development to get some diagnostic data out of our device to an Android app.
Until recently, Android has been happy to grant a connection...
Hi,
I have an i-Jet Debugger.
Please find the details at the below link:
www.iar.com/.../
Can i use this to program softdevice & Bootloader on my nRF BLE chip.
Can...
Hello Everyone,
When i use malloc function in on_ble_event function ble advertising get stuck and not working
below is my implement code:
static void on_ble_evt(ble_evt_t...
Hi all,
I am using an nrf51422 DK as a peripheral, with s130 softdevice and sdk11 on Keil, and iPhone6, with iOS 9.3.1, runing nrf Toolbox UART app.
I am sending data...
Dear All,
NRF 24L01 communication fails particularly @ midnight / early morning 1:00AM to 3:30/4:00 AM and resumes Automatically.
In my project, I have 1 base station...
I was reading a line of code:
mesh_gatt_evt_t* p_gatt_evt = (mesh_gatt_evt_t*) p_ble_evt->evt.gatts_evt.params.write.data;
And ble_gatts_evt_write_t::data is the cenerpiece...
Hi, I'm an undergrade student.
I use Android-NRF-UART in GitHub/Nordic.
I want to enter the encryption about send message and decryption about receive message.
so...
Hi all,
I wanted to know the power consumption in ble device while advertising as well as while scanning. please if anybody knows about it, let me know soon.
Any help...
Hi
I am trying to start an advertise. If I use the “BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED” flag all work’s pretty fine, but whenever I change the flag to “BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE...
Is it possible to have a fast advertisement interval (for connecting and bonding/pairing) for example: 40msec; at the same time, have a slow connection interval (after connection...
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED |
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;
And then when I look up "BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;...
Hallo,
i'm trying to test my BLE aplication using the PTS. The profile test are mostly OK. But if i run the GAP Test (especially TC_BROB_BCST_BV_01_C) the PTS does not...
It seems that static and global data is NOT set to zero during start-up. This is supposed to happen according to the C-standard. How to do this in a proper manner, i.e. to...
