I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
HI,
I have a remote control with nRF24L01. It was talking with Gen1(uses nRF24L01) product via ESB. Now, I am developing Gen2 product*using nRF51822xxaa) and I need to support...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
EDIT
I think there is somewhere in KEIL or nrf libraries a bad pointer type alignement .
The correct pointer is given as uint_32_t ( NRF_SAADC->RESULT.PTR = (uint32_t...
I notice that each dev board has a version of nrf_drv_config.h in the config folder. For my custom target, I want to create my own version of this file where I will modify...
I use nRF52832 as a master to communicate with ads1292. then I want to config the ads1292, so i should send the register address and configuration data.But I don't know how...
Hi,
I tried to compile my own program with eclipse and GCC with c/c++.
I followed this tutorial : TUTORIAL
I have some problems :
First : i have problem with...
Hello,
I developed a code (softdevice S110 and SDK 10) on a prototype based on a NRF51822G2 chip. I tried to reproduce the prototype with NRF51822H0 chip.
I flashed...
Hi,
I use ESB protocol, and all is working fine :)
Now I want to retreive the address of the sender because I can have multiple sender in my network.
I can add this...
With there being +/- 4dBm variability in output power from nRF52 to nRF52, each device needs to be calibrated in order to comply with FCC rules. One of the rules is there...
Hi
I'm porting a nrf51822 project with S110 to a nrf52 board. In this case, I'm a bit confused about which softdevice to use. S132 it is the equivalent to the S110? Or...
Hello everyone,
I am using the nRF52832 rev 1, i am not using the softcore. When the cache is enabled as below, the performance actually seems to get worse.
F_NVMC-...
using Bluetooth Developer Studio, and
nRF52 SDK v11.0.0 - Experimental: Bluetooth Developer Studio Example
I have created a profile using BDS and generated the files with...
In order to teach a class of students using nRF developer boards I'd like to use the nRF Blinky application running on Android, iOS, or whatever mobile platform. The problem...
