Hello,
I tried to use the Cellular Monitor app within the nRF Connect for Desktop software, but it encountered the following error. I have included the relevant part of...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
Hello,
Recently, my team has been struggling with an issue regarding a nRF5340 device that's encapsulated and inaccessible to be flashed with a JTAG connection. Our normal...
Hello,
I’m currently working on a Bluetooth Mesh project using Nordic Semiconductor devices, and I would like to get guidance on static provisioning and group-based communication...
Hi, I'm currently working on an application with the nRF9151, and will use the shadow concept to change parameters used by a device externally connected to the nRF9151. Intended...
Hello ,
I've been trying to build the wifi shell example sample for my nrf52840dk with a nrf7002ek shield. I'm setting the shield via CMakeLIsts ( set ( SHIELD nrf7002ek...
I am new to Nordic Evaluation Kit.
I am working in Nordic nrf51822 (PCA10001) Evaluation board.
Following are my setup.
OS : Ubuntu 14.04 64 bit.
SDK : nRF5_SDK_11...
Hi all,
I need to know the RSSI Value (distance) between my nRF 51 DK and my connected device (iOS Device). I made these code changes:
switch (p_ble_evt->header.evt_id...
Hello!
I've been using RTT viewer to view some data in my nRF52832. Everything works fine but I am unable to clear the RTT viewer terminal screen.
As it is in the manual...
Hi,
I am trying to get the experimental NFC example "HR with pairing over NFC" to work.
I can read the tag correctly with an android phone : the NDEF message is correct...
Dear All：
My NRF24L01+ use Dynamic PayLoad,What register need configure NRF51822?
NRF24L01+ Configuration as follow:
SPI_RW_Reg(WRITE_REG + DYNPD, 0x01);//Enable...
Hi,
I've been using the ble_app_uart example as a template for our use case. It is a good starting point. We don't actually need UART functionality, and we've assigned...
Hi,
during programming, we receive error as in this question . The hex files do not overlap.
It seems to happen only when the board has already been programmed before...
Hi,
I have an application that requires watchdog to run continuously. And from application I have code that jumps to the bootloader without device resetting using bootloader_util_app_start...
Hi,
Side effect of adding a LFCLK of 32.768khz with 90k ohm ESR oscillator? where as data sheet recommends Max value of 80kohm.
Side effect of adding lower drive level...
Hi everyone,
I activated softdevice writing protection with nRFGoStudio (i.e. so that the softdevice can not be overriden). How can I deactivate that again so that I can...
Just to make sure: Will The spi_master_send_recv return when it is done writing and reading, or do you have to have some event wait functionality listening to SPI_MASTER_EVT_TRANSFER_COMPLETED...
I was playing around with the gpiote example under exaples/peripheral/gpiote. The example uses a timer, ppi, and gpiote to blink an led. By default, the app uses Timer 0 and...
Hello.
How to write custom firmware updater, which:
Takes new firmware from other device on SPI or I2C bus.
Writes it to flash ("bank1" at 0x1B000, or...
Hi;
I'm studying on SPI communication at nRF51822 (not DK) but i could not find the pins for spi communication, i read at somewhere SPI is only used at DK(developer kits...
