I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi guys
I am planning to develop a beacon app, but I am not sure what would be the minimum scanning interval in order to keep the phone's battery drain on a fairly good...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
Hi, there! nRf Toolbox drove me crazy!! can anyone help me?
I flash "s130_nrf51_2.0.0_softdevice.hex" to the pca10028 board.
I compile the bootloader example "nRF5_SDK_11...
Hi,
I'am having an issue with UART using app_uart_fifo.c (SDK 0.9.2). At times I get communication error (usually at attaching and detaching uart connector) and my error...
Hi.
I'm little worried about our bt sensor power consumption.
We are using twi/i2c to communicate with sensors periodically. We are using app timer to trigger these...
I have a custom board that doesn't use the external 32Khz crystal. The engineer that designed it chose to use P0.0 as UART RX. (I know, poor choice.) I have set up a custom_board...
I am using SDK_11 s130. I see APP_ERROR_CHECK(err_code) being used throughout the SDK examples. When err_code is any value other than NRF_SUCCESS, the nRF51-dk board will...
Previously, I was able to program ble_app_uart using SDK_11 s130 into nRF51-dk. Now, I would like to program ble_app_uart into Adafruit Bluefruit LE friend board. www.adafruit...
I have been following the advertising tutorial and decided to start my own application using nordics git repo as a reference. After a few debug sessions I found that I needed...
I am trying to probe sysclk signal on one of the unused GPIO pins on a nRF52 board. I modified the ble_app_template example provided in SDK 11.0.0 and added a sysclk function...
I am trying to connect nRF52 with 7120 and create a NFC card reader , is this a solution and power efficient solution .
I will interface through I2C , is there a example...
I am using the sdk version 11 and arm-none-eabi-gcc version 5.4 on linux mint to compile the blinky test application. I have pointed the Makefile-posix at the location of...
I am doing the test about timeslot with the project link text
but it cannot scaninng and i found the timeslot is work because i get event NRF_EVT_RADIO_BLOCKED and it call...
Hello,
my application has to emit measurements in the manufacturer specific data structure continuously and has to accept a connection, for example for ANCS. Therefore...
