Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi,
I am testing the Bluetooth function on my custom board with nRF5340 CLAA chip. I have tested the clock, I2S and SPI on this chip previously and they all worked perfectly...
We have been evaluating the nRF5340 and nRF7002 for use in a new product and we are currently looking at our Wi-Fi FOTA options. For reference, we are using an nRF7002 DK...
Hi Nordic team,
We are developing two types of devices based on the Zephyr examples:
periodic_adv_rsp
periodic_sync_rsp
Our design uses the following...
Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
Hi I have problem with LFCLK timer. In os_tick_init() in RTX_Conf_CM.c there is a loop and it won't end.
while (NRF_CLOCK->EVENTS_LFCLKSTARTED == 0)
{
Do nothing.
...
gaps.zip
Hi,
I have a code that continuously toggles a pin(I use nrf_drv of gpiote+ppi+timer2 for this purpose and interrupt time = 30usec). I have basically taken the...
I know the things like the TWI allow you to send additional data when you instantiate a transacation. Is there any way to do a similar thing with UART?
I'd like to pass...
Hi
I'm using the PeerManager/FDS/FStorage in my project since a few months. We have this software running on real hardware and on simulated environments. While researching...
Hi NORIC's Engineers:
I am a handware engineer who is from Jetway company in China.
I am sorry for my english skill to descripe my questions about NFC antenna of nRF52832...
Hi!
I'm am working on a project where there I need to connect two nrf51 modules and a phone.
Say: Module A, module B and phone P.
The setup i a bit tricky to explain...
I want to use three ADC-inputs on my nRF51832 Engineering Sample B. I read that it is possible to define several ADC-Channels and if a ADC Sample is triggered all Channels...
Hello,
i have a characteristic kept in user space with VLOC_USER. It has read/write with response props and has auth permissions set, both for read and write.
In the...
'morning, I'd like to know how to wire a BMA250 to a nrf52832 please ?
Screenshots : (BMA250) http://prntscr.com/bil9ng
(nrf52832) http://prntscr.com/bil9uu
Thank...
Hi
I've discovered last week some unexpected resets by the watchdog. I guess I've the explanation and the workaround for the behavior, but it would be great to have this...
Hi I am working on activity detection using ADXL362 and nrf52. When I am moving the accelerometer ideally I should get activity interrupt in status register and when ADXL362...
Hi,everyone,
In my project ,I want to save some data when disconnect evt happens; here is my code:
the problem is ths program always stuck in power_manage() function; what...
I'm basing my schematic and antenna design using the PCA10028 as a reference.
I'm not including the J1 RF-connector into my design. Do I still need to include both C6 and...
I only hope that their devices can link their mobile phones, other mobile phone links may not link, but I didn't want to enter a password, directed broadcast method can, about...
I am using the nRF52832 as a MCU in the wearable device,now i want to use the spi master mode to collect data and store data ,and when it is necessary,I want through the bluetooth...
