Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
We use the Nordic UART Service in development to get some diagnostic data out of our device to an Android app.
Until recently, Android has been happy to grant a connection...
Hi,
I have an i-Jet Debugger.
Please find the details at the below link:
www.iar.com/.../
Can i use this to program softdevice & Bootloader on my nRF BLE chip.
Can...
Hello Everyone,
When i use malloc function in on_ble_event function ble advertising get stuck and not working
below is my implement code:
static void on_ble_evt(ble_evt_t...
Hi all,
I am using an nrf51422 DK as a peripheral, with s130 softdevice and sdk11 on Keil, and iPhone6, with iOS 9.3.1, runing nrf Toolbox UART app.
I am sending data...
Dear All,
NRF 24L01 communication fails particularly @ midnight / early morning 1:00AM to 3:30/4:00 AM and resumes Automatically.
In my project, I have 1 base station...
I was reading a line of code:
mesh_gatt_evt_t* p_gatt_evt = (mesh_gatt_evt_t*) p_ble_evt->evt.gatts_evt.params.write.data;
And ble_gatts_evt_write_t::data is the cenerpiece...
Hi, I'm an undergrade student.
I use Android-NRF-UART in GitHub/Nordic.
I want to enter the encryption about send message and decryption about receive message.
so...
Hi all,
I wanted to know the power consumption in ble device while advertising as well as while scanning. please if anybody knows about it, let me know soon.
Any help...
Hi
I am trying to start an advertise. If I use the “BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED” flag all work’s pretty fine, but whenever I change the flag to “BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE...
Is it possible to have a fast advertisement interval (for connecting and bonding/pairing) for example: 40msec; at the same time, have a slow connection interval (after connection...
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED |
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;
And then when I look up "BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;...
Hallo,
i'm trying to test my BLE aplication using the PTS. The profile test are mostly OK. But if i run the GAP Test (especially TC_BROB_BCST_BV_01_C) the PTS does not...
It seems that static and global data is NOT set to zero during start-up. This is supposed to happen according to the C-standard. How to do this in a proper manner, i.e. to...
