I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello,
I have a capricious component on my TWI bus, and sometimes my nRF52 do an infinite loop in file nrf_drv_twi.c
in this loop
while (!nrf_twim_event_check(p_twim...
Trying to connect nRF52-DK with Nexus 5 (Android 6.0.1) SDK 11 NFC HRM example
But can see this device in paired devices list. Next time i do it it never attempts to...
hi,
i have a timer which is being called each second. when i give timeout less then 1 second then the code executes properly and goes to event handler. but when the timeout...
Can you tell me how to integrate this library so that my code works with it? I'm new to using both these OLEDs and Nordic Semiconductor based devices. THanks
I'm trying to write a firmware for PCA10001, which works like a bootloader. In other words, it can download some data into the Flash. To avoid conflicting with the existed...
Hi thank for reading with your kindness
I used keil with nrfready_desktop_2_/* files
when I clicked "Start/Stop Debug Session" with simulator in debugging session, ...
HI,ALL
i notice that the buttons_leds_init is initiating the bsp function.
just like LED and Buttons.
uint32_t err_code = bsp_init(BSP_INIT_LED | BSP_INIT_BUTTONS,...
I recently purchased nrf51-DK. I was going through a getting started document which said to update the firmware on the board. After updating it the boards just keep disconnecting...
Hi:
There is a worried question around me.
when i put my product and phone in a firm place after the product connect with APP of phone.
I find that there are lots of...
L.S.
For our products we have chosen to use the RFDigital RFD22301 (previously RFD51822) product which has a nrf81522 chip inside.
Last year we discovered some issues...
What are the S130 SoftDevice v2.0.0-7 alpha iROM and iRAM settings for the nRF51822 and the ble_app_hids_keyboard example?
Someone at Nordic Support suggested the following...
Hii Nordic guys,
I'm trying to test the example project examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay so I just compiled and trying to flash on...
Hello
I am developing an application with BLE and I have just faced to a problem.
I want to check my IDE settings and development environment.
I am using the development...
A good problem to have... we're only seeing 300nA current draw with a 3V lithium primary while in SystemOFF on the nRF51822, using LDO.
Is that correct? We've measured...
HI , ALL
i added a event in the function 'on_ble_evt' like followings:
case BLE_GAP_EVT_ADV_REPORT:
printf("Start Advertising\r\n");
break;
At first i think...
