Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello everyone,
I want to know if it is possible and how to show advertising data on display lcd (20x4 or graphic lcd). I'm using PCA10028 board with S120 and Nokia5110 LCD...
Hello,
I have read through the pstorage documentation here: devzone.nordicsemi.com/.../a00018.html
and I followed the tutorial here:
devzone.nordicsemi.com/.../
...
I created a bsp folder dfu_dual_bank_serial_s120 from PCA10028/dfu_dual_bak_serial_s13 in examples/dfu/bootloader/PCA10028.
This is for supporting DFU over UART for our...
I am using a development board PCA10040 with an nRF52832
I am running one of the examples: gpiote_pca10040
Everything is working fine with this line in the original...
Hi,
My development platform is a central device that there is a WiFi function, I want to set BLE channel map to avoid from overlay. Let my central device can coexistence...
I am using peripheral example(blinky) to generate .zip file using nrfutil python script. I am getting fallowing error.
nrfutil dfu genpkg --application nrf51822_xxaa.hex...
I am getting fallowing error while update app through uart using nrfutil command.
nrfutil dfu serial --package ble_app_hrm_c_s12o.zip -p /dev/ttyACM0
Upgrading target...
Hi,
I'm building a product using RF Digital's Simblee that uses the nrF51822 ver 3 chip. I've narrowed down a TIMER accuracy issue to BLE. The code below starts and stops...
I'm going to make temperature logger in NRF51822.
I want to use ble_app_uart as reference.
When mobile app is connected I have to send kilobytes of logs.
Now I use ble_nus_string_send...
We have used FreeRTOS a lot, also on nRF51 and nRF52. Now I'm trying to migrate our nRF52 code form SDK11-alpha and SoftDevice 2.0.0-7-alpha (?) to the most recent versions...
Hello,
I am a writing my own code for MDBT40P to blink LEDs. I have configured the LED pins and added all the necessary headers in the project. But every time i build the...
Hello
I am trying to develop my Redbear Lab's BLE mini with Nucleo F401RE since I don't have any J-Link segger and USB dongle.
Is it possible to write program through...
Hi.
I'm using PCA10028, SDK10.0.0, S130 as central.
I'm using "sd_ble_gattc_write" when i want to send string to peripheral.
But if i send this function continuously...
Hi,
For example: In scan and connected as peripheral at same time. When disconnect event happen, how do I know who is the trigger, the center or peripheral?
Thanks.
