Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
I have merged all the 4 file's together (app.hex, app_valid_settings.hex, softdevice.hex and dfu.hex).
Then I uploaded the custom app with dfu services enabled using nrfgo...
Hi there,
I'm porting an app from NRF51 SD130 to NRF52 SD132, both with sdk11. I do the usual stuff, like changing includes, freertos ports libraries, etc, and everything...
Just a general resource question. The Softdevice uses RTC0, FreeRTOS (by coded default) uses RTC1. So in order for the SDK ble_conn_params.c to run properly I have to link...
I was able to add the Device Information service as well as a proprietary service using a 128 bit UUID. I modeled after the ble_peripheral uart example. However when I try...
Nrf52/Kiel/SDK11
My application was at the point where I needed to add DFU. Following the examples and SDK doc, I added the files and code needed. It would NOT advertise...
We recently moved from SDK11 to SDK13. We run out of memory when adding custom services & chars to the S132 v4.0 softdevice. Increasing the app start address in the linker...
For the record I have been struggling with migrating a project from S110 @ nrf51422 to S140 @ nrf52840.
Quite by accident, I found this "nrf51_to_nrf52840.h", what does...
Hi , Everyone!
Now i have the board nrf52832 and i'm conducting my DFU.
My DFU is to update softdevice and application.
Here is detail about my problem:
softdevice...
Hi
From s140_nrf52840_5.0.0-3.alpha_migration-document, it is mentioned that the L2CAP API has been completely removed. Are there plans to re-expose the API? We have exposed...
I'd like to clock the nRF52840 at the same frequency as my converters. Is there any problem with using a somewhat different frequency than the 64 MHz (or 32mhZ) crystal? If...
Hello guys,
i randomly get twi error busy 17.
i have #define TWI_DEFAULT_CONFIG_IRQ_PRIORITY 7 in sdk_config.h and .interrupt_priority = APP_IRQ_PRIORITY_LOW in init function...
My setup is based on a jlink clone and yunjia module nrf51822 and nRF51_SDK_10.0.0_dc26b5e. I am following this tutorial successfully till the section Enable auto discovery...
Hi,
The following function/macro is missing in SDK 12.2.0 and 12.3.0 but existed in 12.1.0:
nrf_drv_saadc_gpio_to_ain
I am re-compiling "thingy" SDK and it happens...
I'm looking for an answer as to how to know the source files that I need to mention in the Makefile if I'm writing my program from scratch. Are there some bare essentials...
Hello,
I am writing here because I am trying to change some concrete values from a .hex file in order to vary some BLE and other values. I need this because I need to generate...
