I have a zephyr zbus project running on the nrf52840DK that’s working well. We want to port the project to the nrf54H20DK, but I’m having trouble seeing the log messages....
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello,
I tried to use ADC on pin 31 (A7) in my project* and i have something strange. It looks like if my pin is pulled down inside the nRF52. Does someone have any clue...
Hey guys,
I am currently using the proprietary protocol on the micro_esb.c library with the nRF51822. So far everything has been working great, but I am certain my transmission...
Hello,
I'm trying the bootlader of SDK13.1, with SD S132_nrf52_4.0.2
I manage to send a ZIP file to the bootloader, but the application doesn't launch. I've tested with...
Hi,
I measured the current consumption of nRF52DK with the original code of "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\ble_app_beacon ",
based on the current measurement...
Hi everyone,
I was wondering if anyone benchmarked the time for reading a word from flash on the nRF52840. I was able to find the write/erase time on the specs document...
Hi,
We use the nrf app (Android smartphone) to establish BLE communication with trackers designed with nrf51822.
When trying to connect, sometimes it works, sometimes...
Hello， for the past I've been trying to migrate unsuccessfully my code from nrf51 to nrf52840 S140. Now that I'm unsuccessful, I'm trying to eliminate the possibility of a...
Using FreeRTOS to run nrf_cli. When Serial is not connected (as in RX,TX,GND) the board goes into a reset loop.
There are a few things that seem to help:
Don't run...
hi,
i have tried to write data into flash memory, but i can not, i can read the data from memory.
i had followed your instruction as this link
infocenter.nordicsemi...
In my project, an android phone is needed to connect to two ble devices. All my ble devices are nrf51822. The android phone can connect to and receive data from every device...
Hi,
to investigate a timing problem in my Bluetooth stack, I've hard wired the Radio ADDRESS and END events to a GPIO pin using the PPI. The ADDRESS event is used to toggle...
Hi,
I'm developing a FW with a lot of services and characteristics. Since I added the ANCS service, I have the "NRF_ERROR_NO_MEM".
Configuration : NRF51822_XXAC / S130...
hello everyone,
i use nrf51822-QFAA(256kb flash,16kb ram).i want to use sdk12.3.
at first i can't build the project,after i install some tools, i can build it ok.
...
i am using nRF5_SDK_13.0.0-1.alpha_055eef3 s132_nrf52_5.0.0-1.alpha_softdevice and used examples\dfu\bootloader_secure\pca10040\ for secure DFu OTA .everytime i try i get...
