I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I'm using nRF52840 and S140 based on the ble_app_hrs_rscs_relay example. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu...
Within a buttonless DFU application should nrf_dfu_flash or fstorage be used to erase and write to flash?
SDK 13.0.0 - Soft device s132_nrf52_4.0.2_softdevice running on...
These messages below appeared when I built bootloader_dual_bank(sdk11) in the eclipse.
'Building target: bootloader_dual_bank_s130_sdk11.elf'
'Invoking: GNU ARM Cross...
I want to have blinky orange led,
0 mean on, 0x8000 is off, right? and why??
I have no idea what's 0x8000 mean!
so if I want have orange(full-R and half-G), how can...
I'm trying to debug my UWP Central app, which interacts with our device based on nRF52/s132. What I think I'm seeing with my packet sniffer (the nRF51 sniffer, incidentally...
I have set the
advdata.include_ble_device_address = true
in advertising_init function. However, the mac address data is not shown in mobile APP.
Is it due to the fact...
I would like to include multiple p_chunks in one record. How do I do this? I've only seen examples with one chunk per record, but fds_record_t.data has a field called number_chunks...
Hi, I am considering using nRF24L01 for a project, and I wanted to use one single transmitter to send data to various receivers (more than 6).
I have found some information...
plss, help me . i can flash other examble nomarlly . But when i tried to flash ble_app_uart to nrf52832 seem previous program still works and new program not flashed yet ...
Hello,
I'd like to store a large amount of data in flash and in a chosen area. As a start, I've chosen the area starting from 0x77000 and ending at 0x78000
Iv'e written...
I have been testing out with NRF52840 and verifying the data transmission using the NRFConnect app on my mobile. I am not sure what went wrong! It's no longer advertising...
Hi!
I have a small issue with one of my current project. I've built myself a custom board using the nrf51822QFAA. And I am using an stlink (on an stm32f4 discovery) instead...
Hi,I have tried to write some characters like device name for BLE device. When I called
Code:
grantPermissionCharacter?.service.peripheral.writeValue(data1, for: grantPermissionCharacter...
The bluetooth icon in the status bar is gray, not white although I connected ble_app_hts(PCA10028) with nRF Toolbox(android app).
Doesn't android recognize connection state...
