Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Hi,
I am having some issues transferring data from an iPhone to the nRF51822.
Actually, I write block of 16 of my data from the iPhone on a specific characteristic on...
Hello,
I have been reading the documentation about how to program a BLuetooth Low Energy application. In that document, a lot of references to an specific mannual (nRF51822S110...
I am writing one bootloader to decide two apps resided in 0x14000 to 0x40000 with nrf51822 to run. Two apps works fine when starting running itself. But when bootloader switch...
Hi experts,
i found one issue that if i continue to make the 51822 advertise(if advertise timeout, start again), sometimes the 51822 will stop in somewhere. I'm sure that...
I have just acquired the NRF51822 Evaluation Kit and going through the getting started documentation. I can't seem to fix a compiler error which is highlighted in Kiel uVision...
Hi,
I am starting my first project with nRF51822 for my thesis.
I thought its a good idea to start with evolution kit so I bought nRF51822-EK
I assume I will get everything...
Hi, I'm trying to run your ble_app_hrs on your nrf51822 chip using internal rc clock: NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION, so I pass this to the BLE_STACK_HANDLER_INIT...
Hello,
I have just bought an NRF51822-EK to familiarize myself with the micro-controller for a potential future job. Admittedly I feel like I am completely in over my head...
I've made a custom board with an nRF51422. The nRF51 part follows the reference schematics almost identically. After overcoming some reflow issues this board seems communicate...
where is nRF51822 example code appropriate to "nRF Temp App" ?
I have successfully installed "nRF Temp App 2.0" on Nexus 7 with Android 4.3.
Now I would like to run the...
Hi,
I want to install the nrfgostudio_win-32_1.15.1_installer,but is's fail.nrfgostudio V1.14 can be installed sucessfully.I still use the command line to install the nrfgostudio...
Hi,
Sorry for the noob questions but I'm trying to understand the GPIOTE abstraction and terminology, specifically the events, interrupts and tasks. My understanding is...
Hi
I have a question when I use the l01+.
I donn't use the Auto acknowledgement and Auto Retransmission, interrupt does not reflects on the IRQ pin and leave the IRQ...
