Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
nRF5_SDK_11.0.0_89a8197\examples\peripheral\saadc\pca10040\arm5_no_packs
Which timer is used in this example? RTC timer or Timer0-4 ?
I can not find it.
Thanks...
Hi,
I have used nRF51 DK board for 6 months well.
Then now, it isn't connected with nRFgoStudio since I have upgraded nRFgoStudio about 1 month ago.
Error message is no...
Is there any reason I can't have the radio notification run at priority 0? By definition it will never run at the same time as the lower stack, so it seems like I should be...
hi nordic
Have a code project sample shows the typical use Flash applications in data storage?
I see
[code]( infocenter.nordicsemi.com/index.jsp .
my code
`
#define...
If I have a high-priority interrupt (or a series of them) that runs long enough to completely mask a radio notification, then all further radio notifications appear inverted...
I bought two EZAIRO 7150 SL hybrid board, (which contains a MOTHERBOARD & DAUGHTERBOARD). As part of the problems we have been having trying to establish a wireless connection...
Hi, I am developing a software that connects to nRF51822 over UART. I donot have the physical device currently so I downloaded its Soft device under the impression that it...
Hi,I update my MDK from 4.7 to 5.0,my old project can open ,but can't find the device list.I want to use 5.0 and 4.7 at the same time,and I have installed the SDK6.0 when...
Hi, when I compile my project the linker gives me the following error:
._build\nrf51422_xxac_s130.axf: Error: L6200E: Symbol GPIOTE_IRQHandler multiply defined (by app_gpiote_fast_detect...
I am working with nRF52832 and SD 132 and SDK 11 (nRF5_SDK_11.0.0-2.alpha_bc3f6a0).
One of my BLE services has a characteristic with an attribute larger than 22 bytes. It...
i was working with a nrf51822 module.after about 50 that i programmed the chip with my jlink programmer (some time i program it with stlink V2) it be damaged and not worked...
I am designing a BLE device. Want to make the PCB as small as possible. to download the code/debug etc I need the a connecter on the board which can connect to the nrf52 preview...
Please excuse my ignorance, My company is designing in the nRF52832 for our first product using both ANT and BLE. From looking at the documentation on thisisant.com there...
I've got a strange problem with updating my Magnet-Characteristic.
I use a service with 4 characteristics (Gyro, Acc, Mag and Temp Values) and update them on a timer base...
