Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
FWLog (1)_formattedByTC.txt Hi,
I am sending data to one of the characteristics from nRF51 to the App(the problem happens in both iOS and Android).
This is what I am observing...
Is there any documentation on the advertising state machine ? This post :
devzone.nordicsemi.com/.../
mentions the state machine and how it progresses from fast, to...
Hi all,
I want to update my connection parameter as follow:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) //400 /**< Minimum acceptable connection interval...
Hi,
I'm doing a project using the Evalution kit.
I don't know why, but I can't go under 350 uA current comsumption in system on.
I did clear all pins,i did NRF_SPI0-...
HI:
i use SPI is ok when i set frequency = NRF_DRV_SPI_FREQ_1M,but SPI will work abnormal when i set frequency = NRF_DRV_SPI_FREQ_500K/NRF_DRV_SPI_FREQ_250K/NRF_DRV_SPI_FREQ_125K...
I am evaluating chips for a new project.
I am looking for a chip that can connect with Sony PS3, PS4 controller and most modern/recent cellular phones.
I am confused...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I tried to modify the twi_master_using_app_twi to work with adafruit ADS1015 as a slave. I ran into this problem. It seems that the init_transfer doesn't finish so the app_twi_perform...
What development kit should I buy? Is this the right one?
www.mouser.hk/.../
What software IDE to use?
Does Keil offer free version for limited code size? What...
trying to build a simple example in sdk 11 just to run it on the nrf52-dk
of course it is missing pieces, else life would be no fun, apparently...
oh, i don't know,...
Sorry for asking as not familiar with BT terminology and un-sure which fold means what, grateful pointer to example (in SDK or similar) that can run on the dev kit. That is...
What is "1 Mbps Bluetooth low energy mode" for nRF52832?
How was the spec. changed from my old year 2013 understanding that BLE is low speed for sensor, sending tens of...
I can read temp value by pulling flag but I Want to do that by interrupt
I added this code to my Keil but interrupt on temp didn't work.
I use Adc interrupt like this definition...
Hi,
We are using NRF51 and STM32F0 on our custom board and one of our customer's requirement is the ability to program both of these MCUs in the factory. They would like...
I am using the mbed compiler.
When I produce code using the "App with Bootloader" option, I can do FOTA updates and my code runs fine, as long as I don't enable the ble uart...
