Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi, i'm wondering if it's possible to make a GPIO pin trigger different tasks when it is externally driven from low to high, and high to low.
I'm trying to stop an RTC...
I would like to NRF51822 bluetooth test.
It has NRF51822 eval-kit 2EA.
1EA is a Central (dongle role), 1EA want to test the bluetooth interlock with Peripheral.
What should...
I hope this isn't a duplicate of another question. I searched on sd_power_system_off and didn't see anything exactly like this.
I'm creating a new project, based on ble_app_template...
I have the 51822 chips, and want to establish a network with large data volume, I use the S130 now, but the effect is not ideal, so I want try the BLE4.2. Do we have the SoftDevice...
Hi,
For the past few weeks I've been trying to make a small device that would simulate a mouse with Arduino and MPU6050 accelerator + gyroscope sensor. I wanted the device...
created a new BSP PCA10001 from PCA10028 and replaced the CFLAGS += _DBOARD_PCA10001 for uart example in peripheral folder using sdk 10.
Migrated simple_uart example &...
Hello,
I wish to communicate with the chip via SPI NRF51822.
The NRF chip is configured as a slave. Based on the SPi_slave_example code, I can't set to 1 the semaphore...
I configured my system to sleep after inactivity time.
nrf_gpio_cfg_sense_input(WAKE_UP, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_HIGH);
err_code = sd_power_system_off...
NRF51822 most time is in sleep mode.
Each 5 seconds it wakes up to make ADC measurements.
But adc_event_handler force only once, but I want to see it every 5 seconds.
...
I'm new to using the RTT Viewer. It was working fine (all morning). I've only been using the SEGGER_RTT_printf(0, "string %d \n",x); call to dump text and data to the viewer...
Hi,
We are using the BLE keyboard example as a basis for a design and notice strange behavior.
Only change was to create a custom_board.h header for a button press on...
Hi,
I can use the DFU bootloader via HCI/UART to update the application image.
Reference DFU init pakcet . The init packet contains a 4-byte value identifying the version...
I searched the database but did not find an answer to my question.
My environment is as follows:
Keil uVision v5.18a
Nordic SDK 11
nRF52 PCA10040
Softdevice S132
...
