I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Using rev 0218 firmware I am getting an awful lot of device errors with the mbed kit. I am not sure if this is a Nordic or an mbed issue so am asking in both places. Symptoms...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
I'm testing SPIM of nRF52 on PCA10040 using S132 and SDK11.
Its base on the app_peripheral_uart example, so I already have BLE communication.
When SPI is not initiated...
I have just received a nRF52 DK board and I am as a start trying to compile the associated Blink program in Keil 5.18 Lite. When I copy the blink example using the Pack Installer...
hi,
I was reading documentation and forum but failed to get a clear picture how AES module work.
So far my understanding is:
There are two ways to access AES either...
I'm building a product that can use the features from your Smart Remote 3. Is there someway to get the reference source files so I can adapt some of the smart remote features...
Hi,
Few days ago I received my DK-52, I set up the development environment based on Keil and started to compile some of the examples included into the SDK. I have not a Windows...
I have been googleing for a solution but have not found any solution yet.
Have tried the following:
Installed J-Link commander. (Does not pick up any usb devices...
We are a newbie team developing some measurement tests with the nRF52832 DK in order to evaluate the BLE from nRF52832 QFAA80 (s132 and pca10040) for IoT applications.
...
hi all,
Question:
i want to print "BUTTON IS PRESSED" continuously when button is pressed and i want to print "BUTTON IS RELEASED" when button is released.
eg: if i...
Now，I use a 1s timer to calculate the clock.
At first,I use the telephone to adjust the time to fit the telephone time.
but finally(after a night ) the result runs fastly...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I'm trying to get a UART example running on the nRF51822 mbed kit. However, flashing any uart examples from the SDK onto the board generates a fail.txt file
What is the...
Hi, i build my own custom board with a NRF52832, i'm having problem with the softdevice (i think so)... my code is base on BLE s132 central and peripheral...
I developed...
I'm using PCA10028 board.
I copied hex file of ble_app_uart project to this board. And then I scanned via my device - Galaxy Note 5, cutting edge phone.
But I couldn't find...
