hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I am struggling with the correct value to use for DFU_APP_DATA_RESERVED in the bootloader. My application uses the Device Manager and has one block allocated for to pstorage...
My app is generating hardfualts. Based on this post I looked at memory location SP + 0x14, which points to the address that generated the fault.
Memory at SP+0x14: 8F 31...
Hello Everyone,
I am doing the rough calculation of the power consumption of NRF51 where in the radio part of the datasheet it is indicating 10.5mA whether it is denoted...
Hello ,
I'm using a couple of nRF52 dev.board (one is Nordic preview dev.kit , the other one is a Rigado BMD-300) , with S212 ant+ softdevice . I'm able to deep-slepp the...
I use the board to act as relay.First ,i scan and connect to one peripheral.Then ,i want to disconnect the peirpheral once the another central connect to my board.i call sd_ble_gap_disconnect...
Hi ,
Would you help me to find right material(App note, source code/project) to implement below case:
My nRF51822 connected on beaglebone black(BBB) over UART this will...
Hi,
I want to implement a DC/DC converter setup schematic for my projet and I don't know how to make the difference between the AVDD and VCC_nRF supply tags given in the...
Hi, all!
I have a Quesion about Maximum Voltage & Current of internal DC/DC conv. & LDO of nRF52832.
I'll design circuit using olny internal DC/DC conv. & LDO of nRF52832...
Hi.
Is there a (lazy) (dummy) comfortable way to make an nRF518 chip (in my case, nRF51822) communicate with the built-in bluetooth adapter of a laptop with windows 7 or...
Hi,
I am trying to connect a GPS through UART to nRF52 and get the reading and write it to the serial USB of my PC. I am using app_uart_init() and app_uart_close(). My idea...
Hi, I would like to handle in the twi_event_handler the case when the p_event->type == NRF_DRV_TWI_EVT_EVT_DATA_NACK differently and not treat it as an internal error.
...
I'm trying to use separate antplus network key, but I still can receive messages from devices that are configured with another key. Device A was using network key 0,0,0,0...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
