I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi, i use softdevice 9.0 and s110 8.0.
I want to make 38kHz pulse.
so i tried to use nrf_drv_timer and gpio.
if i try to make 200us, it worked not bad.
but when...
Hi, everyone.
I have read the nRF5 SDK --> GPIOTE part in the infocenter. However, I have not get anything useful.
I just want to recieve a interrupt from an external...
Hi all,
I have installed the 1.21.1.3 nrfgo stdio from nordic site.
in device manger nordic board is not detecting( both nrf51 and nrf52) only in my lap.
any setting...
Hi
I am working on customization of proximity device with nrf51822 and I need to lock it to first connected device (so after first pairing I have to make blocking connections...
I took the reference of your example and instructions hear -
devzone.nordicsemi.com/.../
The program runs but get struck at sending the I2c write command .
Do I need...
Hi,
just want to make sure: is it possible to merge UICR values into hex so that I can load some values there during production in a single flashing stage?
thanks
best...
I now have my app.hex and bootloader is running at nRF51822 and yet, the nRF Toolbox finds "DfuTarg" as expected. However, after selecting my file the UI surprisingly starts...
Hi.
I'm using nRF51822, SDK10.0.0, S130.
I made "radio test" program as below at the first.
void radio_tx_carrier_test(unsigned char freq_ch)
{
NRF_RNG->TASKS_START...
Hi,
Can we add device address with all fields set to zero's to whitelist.
I went through the spec, but it doesn't talk about the address set to zeros.
Thanks,
r...
Is it possible to change data send in scan responses after each Advertising Event? I know that sd_ble_gap_adv_data_set() has constant input arguments, but it seems weird for...
Hi everyone;
Im trying to use my nrf51822 as iBeacon with "ble_app_beacon" in SDK. As you know for estimating Distance, you should calibrate it. for calibration, place...
Hi,
I have IOS application which works fine with bluetooth different than NRF. I use direct connection by UUID in IOS app. When the application is in foreground everything...
Dear Sir,
I am new in nRF51 and used the ble_app_uart example in our application (nRF51), need power saving function but not necessary power off.
The sample code will...
