I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
Is there a way for firmware running on the nRF52 to detect the presence of a SEGGER (or other) SWD capable device? I've looked through all the nRF registers but couldn't find...
Hi all
Our application, built on the NRF51822 Rev. 3 and the SoftDevice S130 V1.0.0, uses the UART0 with 115'200 baud, 8N1, to communicate with another controller/PC. Hardware...
Hi, In my project I want to read data from i2c and update in advertising data and the board need to advertise without time out (i.e 24x7) for these I take advertising timeout...
Hi,
I am new to the BLE profiles. I am have to send the TMP007 temperature sensor values to mobile APP using BLE HTS profile. for this I am using sample example of nrf52...
My customer offered the P/N#NRF51822-CTAA to us, I tried to find informations on it, but on your data sheet I can only find code QF, CD, CE, CF, nothing on CT. Is NRF51822...
Hi,
I have question related with some parameters of BLE transmision.
Connection interval in my project is set to 10 ms. Peripheral sends a notifications whenever the...
I have the nRF52 dev board and a stand-alone Segger J-Link (not the one that's on the dev board) connected to the nRF52 through the Debug In header.
The firmware that gets...
I'm new to the NRF5182 and I am currently working on a device where I need to wait for the tx register to send all data before i continue the flow of the program. However...
I'm trying to port your eddystone sdk to GCC. At the moment it is already compiling, but when calling softdevice_enable I get 4 as error code. If I'm right, this means NRF_ERROR_NO_MEM...
Hi,
This time I am trying to work out the UART example.
I got it to the point where it is advertising, but the advertisement is wrong.
When I check with an Android...
Hi,
I have not yet experienced well on the design and development an application using nrf51 series. Your help will be very useful for my work. My question is as following...
Hi,
I have some problems with functions sd_ble_gap_disconnect and sd_ble_gap_adv_stop.
I got critical error when i try to disconnect or stop_adv and my phone is connected...
