Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Is the nRF Temp App source code available for download?
I am currently developing an ultra-low non-connectable beacon and would like to use the nRF app as a starting point...
I guess all the Bluetooth members saw the email from the SIG about the next version of Bluetooth and how it is confirmed to have double the range, quadruple the speed and...
I'm looking at table 23.15.2 in the nRF5 Reference Manual, and it states that TX startup current is 4mA with the DC-DC enabled.
Does that 4mA include the CPU idling...
My project: nRF51422, S110, based on SDK 7.1.
My project employs several application timers (run via the scheduler) and a continuously running Timer1-based 1ms timestamp...
Hello again,
i wanna use the UART communication for transfering data from my µc to the nrf51 and vice versa.
For a test i used the ble_app_uart example and it works...
Hi,
I programmed my NRF51 to read ADC samples and I trying to transmit the information to a dongle. So far I have been able to send the hexadecimal values of the recorded...
Heyho!
Is it possible to set the PWM base clock frequency to 40kHz? If so, how? I see that the predefined base clock frequencies don't go any lower than 125kHz.
I'm...
Hello everyone, I am program for PCA10001 and I want to use Bootloader to upgrade firmware through OTA for my device. I have a old file bootloader use for s110, and I tried...
Hey,
I would like to send data from Central to Peripheral. I follow by ble_app_uart example, however I need to send a float type variable, so I split it to the total and...
I have 2 identical nrf52832 development boards with PCA10040 V1.1.0. One is running the ble_ant_app_hrm example from the nRF5_SDK_11.0.0_89a8197. This example appears to run...
Hello,
I'm developing a product using nRF51822 which is intended to work with iPhones (only iPhones for now; iPod/iPad and Android later).
I need some kind of document...
Hello,
I'm trying to recreate the PWM_library example from the v.11 SDK in a new file in Keil. I have compared the debug settings in my project to the debug settings to...
Hi there,
I am following the thread to use JlinkExe and JlinkRTTClient. I encountered a situation which i don't understand.
After running JlinkExe (go to the folder...
