I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic Tech Support!!!
Greetings of the Day!!!
I'm Dinesh Katkar, we team working on wearable IoT design and we need to interface 4 RGB LED-SMLP34RGB2W3 from nRF52832...
Hi：
1： NRF52832 How to set up the TX transmission power.
ble_app_hrs ：didn't see set TX transmission powe
2、NRF52832 ：How much is NRF52 maximum rate, how to set
THS...
What are the certifications required for Australia? My device has FCC and CE certifications, are these enough to allow someone to import my device? We are both really unsure...
I'm using the nRF51822 DK + SDK10.0.0 + s110. I'm going to create a system where I do an SPI read from two sensors every 6ms. From these sensors I will get 20B each over SPI...
I'm writing a program sending die temperature data through BLE. I'm trying to combine the nrf51822 Heart Rate Monitor example and the nrf6310 Temperature example. Both examples...
Hello,
I have connected a SX1272 module to a nRF51 Development Kit using the Arduino connectors. Anybody written a sample app to get me going?
There is a SX1276 Ping Pong...
Hi all,
We have implemented the wireless mouse example on some custom hardware and it works great. We need to do something a little different however, and send absolute...
I can run peripheral examples in SDK folder like GPIO, Timer, Scheduler ...
but when I want to Add somethings like GPIO to peripheral_UART_ble or timer or scheduler It didn...
Hi Nordic Community,
I am using the nRF51822 to receive a data stream from the SPIS module and transfer the data directly to a phone over BLE using the S130 softdevice...
This is a follow-up question to devzone.nordicsemi.com/.../
I am using SDK_11 s130 on nRF51-dk.
I discovered that on nRF-UART Android app, notifications are not enabled...
I managed to enable pairing without bonding on ble_app_uart by porting peer manager over from ble_app_gls. I am using SDK11 s130 on nRF51-dk.
I observed some strange behavior...
Hi Nordic's community,
I have an issue when writing uint32_t to a characteristic, i don't understand when i write uint16_t or uin8_t, it works ! but don't when i send an...
Hi,
I would like to add single bank signed DFU support to my project (running on nrf51822AC - 256kb version).
In SDK 10, there was an experimental bootloader with a nice...
Hi,
I want to transmit adv. data AES encrypted everytime. The Basic requirement is to do Encryption with Stream Cipher (Counter Mode) so i want to know when and where to...
Hi,
I am trying to get bonding to work in both iOS and Android versions.
As per the suggestion in : devzone.nordicsemi.com/.../ I used
attr_md.read_perm.sm=1;
attr_md...
