Hi,
I am currently building software on NRF 52810 and softdevice version is s112 7.0.1. I have one service which has three characteristics. When I add either a new service...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Dear Nordic Support Team,
We are currently exploring the use and potential benefits of the paEventCounter as described in the Bluetooth Core Specification 5.4, Section 4...
Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
Hello,
I am using ble_app_multilink_central example as a foundation of my app involving central - peripherial connection (S120 - S110). My app works nicely but i have problem...
Hello, I am trying to establish a connection between the nRF52 board and the USB serial converter TTL-232R-3v3.
The setup is such that I connect the converter cable to...
Hi all,
we have a project based on nRF51422, SDK 6.1, Softdevice S310 2.0.1.
We use the bootloader for DFU services. Our problem is to send a service changed notification...
Dear all, I had debugged example Heart Rate Service from SDK 9.0.0 without problems but I think we have a exception, when I insert a breakpoint on line 923 instruction APP_ERROR_CHECK...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
We designed our own board using nRF8001 and EMF32, I used the EMF32 development kit to test the code and it is working fine. When I down the same code to my own board, it...
Hi ,
I am planning to implement S120 UART to communicate with desktop as well as S110 UART BLE.
I browsed in the forum and found out we already have example in github...
I have a small nRF51822 module that I want to use for UART communication without handshaking, and I'm having problems with reliability. Basically the nRF51822 crashes and...
Hi, I've got a pretty basic question, but I haven't found a satisfying answer for it. It is obvious, that the CC registers are 32 bit wide, but because the RTC Counter is...
Hello:
Does the nrf52 radio peripheral EasyDMA write to PACKETPTR on byte boundaries or does it write "bits"? Suppose I have the ADDRESS_BCSTART shortcut enabled and the...
Hi all,
I can use the API sd_ble_gap_rssi_start to start RSSI and can get the value when the BLE_GAP_EVT_RSSI_CHANGED event occurs.However,when I use the sd_ble_gap_rssi_stop...
Hi, I'm recently concerned with the latent risk that nrf51822 might be hacked by extracting the firmware also known as "snarf"ing.
And I know there is Memory Proection Unit...
I followed the guide of github.com/.../nRF51-ble-bcast-mesh to try the mesh with NRF51822.But there seem no discribtion about which softdevice we should use.I loaded the s110_nrf51822_7...
