I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi.
I'm using the arm_sin_f32 function to generate an array of sine wave values. However when this function gets called the softdevice crashes.
I've included:
#include...
I've been trying to chase down some of the engineering samples of the nRF52840 for a prototype with no success from distributors here in Japan (have tried Digikey and Mouser...
Hello,
I know that the NRF_TEMP peripheral is a restricted peripheral and should be accessed with the sd_temp_get function when the soft device is running. Heck I even...
Does the NFC library globally disable interrupts at any point? We're trying to track down an issue where our code occasionally misses an I2C event during NFC read/write.
Hi all,
when I try to send 6 bytes of 0xFF, the last bytes change. I use SPI in mode 3. I use the NRF52832 on a custom board using SDK13 with sd v4. See the following screengrab...
Keil4 compiler in the compiler C and assembly of the mixed code, the error content is: Branch offset 0x00000388 out of range of 16-bit Thumb branch, but offset encodable in...
This function contains a lot of tags that need to jump, but at compile time there are these errors.
this is ARM compilation and C mixed,How should this error be handled?...
Hello, I am trying to develop on the NRF52. I have the development board and have been spending time with the SDK and documentation. I understand how the GPIO should work...
Our nRF51822, S110 device uses concurrent advertising (iBeacons) when connected to the central. Our customer would like to have a variable tx power on the advertising packets...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hello
I adapted the ble_app_uart with twi functionality.
Therefore I included the "app_twi.h" which includes the "nrf_drv_twi.h"
But as visible in the picture, the "nrf_drv_twi...
Hi,
I'm using nrf51822 with soft device s130 version 1.0 and I'm trying to flash hex file of size 108kb from both keil u vision/nrfgo studio.
Flashing is success but application...
Hi
I probably have done multiple or bad inicialization of flash memory in code
and my MiniBeacon ( www.alibaba.com/.../Nordic-bluetooth-nRF51822-logo-customizable-minibeacon_60408141084...
hi..I am using nRF52832 with sd 132 v4.0.2, I want to store data received over BLE in flash. So i wanted to know how much is the memory available to store data in following...
