Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Please can anyone help me on how to use(program) PWM hardware with individual loading mode? My goal is to control 12 LEDs individually with different duty cycles and playbacks...
I want measure the current of a device over a resistor. It is connected to 5V which is over VDD(3V) of nRF52 Chip.
5V--->10ohm--->Device
the differential voltage of this...
Hi,
I am using SDK v8.0.0 , Softdevice s110 and Example is ble_app_uart(peripheral).
i want to reduce a range of nRF51822 beacon(PCA20006) up to 2-3meter..
i try this...
Hi all,
Basically I am doing an exercise on the BLE system use case. Let's say I want to setup a BLE system where there are the long range BLE capabilities in Relays and...
What is a minimal length of preamble, such that nRF51 is able to safely receive a packet with? Can it be made (via some magic registers) to be as small as 4 bits? Then it...
Hello!
I'm pretty new to BLE and Nordic, and hope that someone can give me some good advice.
I'm working on a project were I have 2-4 sensors, each connected to a nRF52832...
Morning,
I ve try to flash the hex pca10040 from the examples/ble_peripheral/ble_app_hrs without success, with the flash seems ok, i can t see the device.
So as i ve...
I found this comment in fds.h as function header for fds_record_write()
* Record data can consist of multiple chunks. The data must be aligned to a 4 byte boundary, and...
Hi guys,
i was testing the connection speed from android in conjunction with advertisement time to see what will work better in my production code.
The result were:
...
Hi, Forum.
I want to make uart_bootloader without softdevice. for this, I want to prepare keil project.
I tryed this but I have some problems.
Basically,
My bootlader...
Hey there!
I am trying to switch from Keil to Eclipse.
I have followed several tutorials on this website ( like this one ) and I can easily create new eclipse project...
Hi,
I use the SDK9.0.0 S130'DFU project in the parth of pca10028\dual_bank_ble_s130\arm5_no_packs\ for testing.I found S130'DFU code is different compare to the S110 of SDK6...
Hello,
I am using MDBT40 ( www.raytac.com/.../MDBT40 spec-Version A5.pdf) in my project. Also I am using arduino IDE to create .hex file for MDBT40 using this reference...
I have the nRF52DK board and I am using that to reprogram the Sparkfun breakout. However, initially, I was using the Sparkfun Beefy UART device to flash the nRF52832 to begin...
This message appears :
Field 'BLE_GAP_CONN_SEC_MODE_SET_OPEN(&hrs_init.hrs_hrm_attr_md.cccd_write_perm)' could not be resolved
but the build and flash were successed...
