I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I ran into an odd issue on nRF52840 using s140 version 5.0.0-3.alpha. My application erases and writes to a region of flash.
I've found that I'm able to erase the pages...
Hello,
I have implemented experimental DFU buttonless example with my application and able to do the firmware OTA via secure bootloader example using private and public...
Hi,
I'm experimenting with the nrf52840 preview board.
I have tried the example "ble_app_att_mtu_throughput" using the coded option to check the extended range and it...
hi, everyone!
I have a question for pstorage, when i use pstorage_store,it was failed, return error code :15 how to solve it. Below is my code
void custom_flash_init...
With good luck, I traced my connection timeout to the slave/peripheral using nrfSniffer. What is most unusual is the slave unexpectedly stops corresponding with the master...
Hello,
I am trying to implement DFU secure bootloader to do firmware update over the air for nrf51822.
I have followed the steps as per the blog
devzone.nordicsemi...
Hello,
I want to ask, did the nordic chip support I2C slave ? I want to make other controller (STM) as Master and Nordic chip as slave in I2C.
Is it possible? or Nordic...
Hello!
I am trying to increase the MTU size to get higher speeds. When I increase the MTU above 65 the application locks/software reset when doing transfer. Up to 65 it...
Hi, I'm facing an extremely strange problem with a product I'm developing.
I've been getting significant idle current measurements (around 7 mA), and I couldn't for the...
I recently attempted to upload a new image via OTA.
After emailing the zip file to my iPhone as an attachment and tapping on it,
then tapping on the share icon several choices...
Hello,
I need a voltage regulator to power a microphone at 1.3V from a 3V coin cell battery and I was looking for a regulator like the lm317 , but with this one the minimum...
IAR EW 8.11.1 does not link the nfc samples from sdk 13.1. There are different sizes for wchar_t:
Error[Lt009]: Inconsistent wchar_t size
nfc_t2t_lib.o(nfc_t2t_lib_iar...
Q1 I compile sdk13.0.0 generate nrf52840_xxaa.hex(app), nrf52840_xxaa_s140.hex(bootloader).
I used merge tool make a hex file, then burn the file into PCA10056 DK by nrfjprog...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the softdevice to work as s130 for its (simultaneous Central/Peripheral...
