Dear Nordic team,
I am currently working with the Thingy:91X (nRF9151) and nRF Connect SDK v2.9.0 , and I am attempting to run the official ECDSA sample from your documentation...
Hello everyone
I need help. I have a custom board that uses the nRF5340 microcontroller. I am using the Zephyr OS and nRF Connect SDK Toolchain v2.9.0. How do I update my...
The direction_finding_connectionless_rx **works fine with NCS v2.3.0**, but with v2.9.0 get's a link error on dts instance for nrf52833dk:
I have top view knowledge of the...
Hello,
To finaly adjust the inside crystal capacitor at the end of production, I need measure the LFXO and HFXO frequencies signals to fine tuning. How should I do ?
Best...
Hello,
We have developed a custom board using the nRF9151, with the design and board files largely based on the Thingy91x. We are using the nRF Connect SDK v2.9.0. When...
Hi,
I want to measure the current draw of the MCU only on the nRF52840DK while I am running my custom code. I want to exclude the current draw of all components except for...
Hello everyone,
I’m fairly new to Android development and currently building a BLE app using Kotlin in Android Studio. So far, I’ve managed to implement scanning, connecting...
I'm trying to build the ble_app_hrs example from Nordic's SDK on a Mac OSX 10.9.2 and have been following Nordic's nAN-29 Note v1.1 to install required tools, while looking...
Good day, I am using a USB to UART IC and it isn't working just because the nRF51822 Tx signal is inverted from this IC. There are some way to invert the UART signals?
I am building a new PCB board for a prototype. It will be used for proximity. It will blink on low battery. It also has a piezo speaker attached to a pin as well. My question...
Hi all. I'm now developing a triangulation solution for indoor robots as a project at my school. I have 4 radios, that I want to communicate with.
One master node send a...
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Attempting to program a softdevice hex file using Keil uVision and an ST-Link V2, I get:
No Algorithm found for: 10001000H - 10001013H
This is in the UICR (User Information...
Hello,
I am thinking about going to eindhoven the 20th of may for the nordic tech tour presentation.
My main interrest is the new v7.0 S110 softdevice which is to be released...
I have used the NRF51822 evaluation kit for a while now to design a product and it performed perfectly up until a few days ago: the onboard segger now fails to connect to...
hi,
i am using a light sensor which is SMBUS serial interface, i tried to interface twi of nrf51822 with the sensor, but i am not able to get acknowledgement from the sensor...
HI,
I'm using sd_app_evt_wait() for getting back to sleep mode between advertisings. I noticed that when I change the voltage in a small interval mode (40 ms between advs...
Hi, If i am running 2Mb radio channels, how many can i have operating in the 2.4Ghz space concurrently?
ALso, what mechanisms can be employed to detect and move frequency...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
Hi,
I'm using Nordic 8001 with Arduino.
I successfully connected to ANCS. The problem is that i need another iOS App that scans for services on my bluetooth device and...
Hi!
My problem is that my code works on the devkit PCA10004(PCB antenna) but not on my own custom board.
The devboard can be connected to and all characteristics can be...
Hello,
i would like to make device which will be dynamically change connection with centrals. It should be connected to the nereast device (with the most power). So I will...
