Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I don't understand why i have a current consumption of 0.535mA in system off.
In my soft i use PWM, SPI a Button,, I put all things off before i go to system off but still...
hi all:
I download the nRF OpenMesh from the GitHub.
There are 4 example in this folder:
(1)Bandwidth_test
(2)BLE_Gateway
(3)ping_pong
(4)Template project
I prepare...
Hi,
Starting from the LED Button Service found in SDK_12.2.0/examples/ble_peripheral/experimental_ble_app_blinky I'd like to add two characteristics on this service. I...
Hello!
Based on you example I try to develop a simple HelloWorld example that follows chapter 11 of the specification. It says that to form a network a energy scan should...
Hello,
I have been investing a couple days now in order to get the DFU procedure working properly, but it seems I am stuck...
This the setup that I am currently using...
Hello,
I seem to be having some errors with my current project. I am using SoftDevice S310 Version 3.0 and SDK 9.0. When i try to communicate with one of my I2C sensors...
Hello,
When using hal_w2_read() and hal_w2_write(), should the 7 bit address of the slave be passed in or the 8 bit read/write address?
It seems to me that passing in...
I downloaded the nrf52 SAADC Low power project from the GitHub
github.com/.../saadc_low_power
I'm trying to migrate it over to version 12 of the SDK and I think I'm having...
Hi. I'm using nRF52832, SDK13, S132V4.0.2.
I'm trying to test DFU.
I have 2 questions.
Q1. How can I make image for merged files?
I can see it works very well when I...
I am in the process of porting an nRF51822 (s130) project to the nRF52840 (s140), moving from the SDK V11 to V13.
I was using the BLE_EVT_TX_COMPLETE event in the SDK V11...
I've seen in two different posts that some people were trying to use this Torex XC9265A181MR-G in terms of being able to use a 3.7V LiPo battery. Can someone tell me if he...
I just bought the NRF51DK and going through this getting started guide: devzone.nordicsemi.com/.../
I opened the file ble_app_uart_pca10028_s130.uvprojx in folder ..\examples...
Guys
I am a newbie using nordic modulesI am just starting to program here with a nRF52 and SDK 12.2
I was trying to edit the experimental_ble_app_blinky and experimental_ble_app_blink_central...
