Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi All,
i would like to know in ble_app_hrs example gpiote_init() is called from main
and then again called in led_start for what purpose it used in 2 place.
can...
I see that we can specify the SPI frequency in bps, I was just wondering how fast the SCK line was oscillating for these values. Does it use the 32.768 kHz crystal oscillator...
If the nRF51 chip is in System Off state, do the GPIO pins retain the pull-ups or pull-downs? If so, what value do they have and how much current can they sink or source?...
Hi all,
when i want to connect different peripheral on central(s120).
it have a error and disconnect.
it seem ok , but that will disconnect later.
ant it get disconnected...
Now I using 51822 to develop a product, I would like to know, can I change the connection interval after connected? or I can only setup the connection interval before connected...
Hi,
is it possible to use the nrf ibeacon which is designed for advertising his data, as i think , to use it also as an observer which can receive data from other beacons...
Hi there,
I am looking for the nRF51 SDK , version 4.3.0
While some previous versions are linked if you click on the version number in the Downloads section (see similar...
Has anyone tried Keil 5.11? I get a parsing error when installing/repairing SDK when it imports the device pack into Keil. 5.10 works great.
The new parser is complaining...
Hi, I cannot install nRFgo Studio 1.17.0.
Installation rollbacks during the installation of libusb 1.0.
My pc has Windows 7 64bit with .Net Framewrok 4.5.
No boards are...
I can't make sniffer working with my HW, everything seems to be working correctly and as described in the help file, but I've never seen any sniffed packet yet. So I've decided...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hello,
We're looking for easy way to communicate between nRF51822 configured as central part with C# application.
Ideally we should use standard firmware which forwards...
