Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello,
I feel like this question has an answer similar to this question, but I can't seem to get it working devzone.nordicsemi.com/.../
I am using the nrf51422 chip...
Hello,
I bought a SainSmart display which fits on the PCA10028 development board. This display is a 16x2 character display with a HD44780 display contoller (I guess).
...
Hi,
i am new in nrf51822.
i want to make a pin as a external interrupt pin, whenever it get high to low pulse it will call in ISR.
here i am unknown how to write an ISR...
hi,
i have downloaded code to nrf52 BLE module using nr52 DK with VTG,SWIO,SWCLK connections. but here i am unable to display the log for nrf52 ble module. is it possible...
Hello, I got the solution for my previous errors, but now I'm facing new error, that now when I compile my code it gives error like invalid command name "nRF52"
ac2...
Hi everybody,
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
The system hangs when doing burst write reg.
MPU9255 can work fine if all writes are ...
I'm having a strange issue with getting SPI running through the transaction manager whilst running a S140 softdevice (SDK13 w/ nrf52840 5.0.0-2Alpha - I know there's a newer...
Hi,
See attached photo for layout placement of the trace antenna.
Altium PCB File : 108-0013-01 PCBA MAIN.PcbDoc
Background :
This is a design for a wearable...
Hello,
I am using SDK 11.0.0 and attempting to integrate the BNO055 IMU into twi_sensor example and then connecting the IMU data over BLE via ble_app_uart.
I successfully...
Hello,
I have two devices sharing an I2C bus. These devices are the MAX86150 and the MLX90614. DMA is being used. I2C is running at 100 KHz.
After initializing both...
Hello,
I'm currently working with sdk 11 on nRF52832.
I'm trying to acquire 20 value from SAADC every 10ms during 300uS.
I think that the rate is too high because...
Hi , why I can't have an update of my bootloader ? Here is the script I use to generate the .zip file :
nrfutil dfu genpkg --bootloader Bootloader.hex Boot.zip
The...
i have RBL nrf51822 ble and i want to try it with BLE Sniffer. i flashed the nrf sniffer hex file by drag and drop to my dongle but it doesn't show anything. only it shows...
Hi Everyone,
I am working on a hobby project with nRF51822 which needs me sample upto 4 signals reliably at 500Hz each at 10bit resolution. I have read through few posts...
