Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
Have project setup to read values from ADC and then run fft_process. Then print them out over uart using NRF_LOG_* statements. However after we call the arm fft functions...
Hello, I am using nrf51822 and SDK11, dual bank dfu ble, S130, 2.0.0.
I made dfu zip file and I modify firmware_crc16 value to the wrong one.
And I zip it again.
But...
hai
i am working with nrf51822 and mbed .
in my application i have requested one page in flash for data store using pstorage.
pstorage_module_param_t param;
param...
Hi,
I'm trying to use NFC type 4 tag on nRF52 side (PCA10040) and poll and read it on Embedded Linux using neard [1]. I'm not an expert in NFC area, so I could be wrong in...
I am migrating a project from SDK 12.1.0 to 12.2.0. According to this question the RAM base needs to be defined in ble_stack_init(). The examples that come with SDK 12.2.0...
I followed the Nordic tutorial on wrapping an SDK sample project in a Makefile managed Eclipse project. I used the ble_app_beacon as the project.
Eclipse will build the project...
I have implemented pwm as suggested in the info centre of nordiac semiconducter. But it showing the following error as shown below image.
Please Help if any one is aware...
Hi,
I think that I found bug in nRF Toolbox release 1.3.0.
1)Application flashing stucks on 95%
2)If you click on Abort, application will stuck in aborting phase. ...
Hi,
Currently I'm working on updating some code based op pstorage on the nRF51822 with SDK 10 an SD S110 (v8).
Right know we're not using "blocks". We're using pstorage_update...
Hi All,
Is there any way to extend RTC2 wakeup interval time more than 2s ?
we know that the maximum interval time of RTC2 on LE1 is 2s, i want to keep LE1 power donw to...
When I just test and build with NRF51-DK there are with BSP Package. such as (pca10028).
But When I make a new PCB Board, Do I have to make my own BSP Package (.h header...
Hi. I have a problem with HID keyboard example. Function sd_ble_gatts_hvx returns 0x00003401. I know that it's means BLE_ERROR_GATTS_SYS_ATTR_MISSING. But how and where I...
Hi everyone,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
How should it be done and what do I have to...
Hello everyone.
I have both the two boards now. If I draw a PCB myself and want to use the Debug-out port to debug my PCB, what should I do? Which pin should be connected...
